| [ Total Views: 691 | Total Replies: 9 | Thread Id: 105757 ] |
|
|
 Lateral
A.k.a.: Greg Hanley
Wolfsburg Wizard
Posts: 480
Threads: 76
Registered: September 30th, 2011
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 14th, 2014 at 02:48 PM |
|
|
How do I get Windows to wind up and down smoothly?
Hi Guys,
Both the windows in both of my cars ('67 and '76) are painful to wind up and down.
Before I start pulling off door trims etc I thought that I would ask to see if there are any tips and tricks to getting them to work nice and
smooth.
Thanks
Regards
Greg
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 14th, 2014 at 03:01 PM |
|
|
Usually the felt bailey channel is the biggest culprit. Both your cars have very different lift mechanisms.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Lateral
A.k.a.: Greg Hanley
Wolfsburg Wizard
Posts: 480
Threads: 76
Registered: September 30th, 2011
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 14th, 2014 at 03:12 PM |
|
|
Hi Matt
Thanks for the quick reply.
Yep, I'm aware that the lift mechanisms are different, I was thinking that there are some things that I should check.
Regards
Greg
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on April 14th, 2014 at 05:32 PM |
|
|
Both felt channels need to be in good condition to allow the glass to slide easily plus the glass sitting inside the channels needs to be clean. Over
time the edges and small area in the channel gets a build up of crud that prevents the glass sliding easily.
Then there is the spacing on the channels. The window shouldn't rock to an angle too much as the point of the glass actually creates more resistance
than the flat edge of the glass.
Both inner and outer scrappers should allow the glass to slide easily and not bind against it.
Finally, there is the mechanism itself. The early style spring clip and sliding runner needs to have a non-rusty and smooth spring, a non-rusty smooth
runner and be well greased. If the surfaces of the spring or runner are badly pitted from rust then they won't slide smoothly against each other even
with plenty of grease.
So start at the top and work your way down.
Oh and Matt sells either WCM or WW seals and they really are the best quality out there. 
madness is in the eye of the beholder  |
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on April 14th, 2014 at 07:10 PM |
|
|
I rub some graphite powder on the glass side of any window scrapers. It stops the glass from gripping them on the way down. Graphite powder is also
good in the felt channels.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 14th, 2014 at 07:45 PM |
|
|
| Quote: | Originally
posted by helbus
I rub some graphite powder on the glass side of any window scrapers. It stops the glass from gripping them on the way down. Graphite powder is also
good in the felt channels.
|
x2
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on April 14th, 2014 at 08:25 PM |
|
|
Hi
I used silicone spray on mine
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on April 14th, 2014 at 08:31 PM |
|
|
its best to pull the winder mechanisms first and thoroughly clean 40 plus years of gunk out of them
also inspect for damage and excessive wear
wash and re wash to remove all old caked grease n dirt then lub with molly and rotate when lubing to get into the gears
YES good new baily channels will help as well and a good spring clip in the window winder channel attached to lower edge of glass also lubricated
well
its a combination of a few little items that make it go up n down easier
|
|
|
pfillery
Insano Dub Head
Posts: 734
Threads: 160
Registered: December 30th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 15th, 2014 at 05:59 AM |
|
|
| Quote: | Originally
posted by 1303Steve
Hi
I used silicone spray on mine
|
+1
Works particularly well on electric windows that are sluggish.
|
|
|
Lateral
A.k.a.: Greg Hanley
Wolfsburg Wizard
Posts: 480
Threads: 76
Registered: September 30th, 2011
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 15th, 2014 at 06:41 AM |
|
|
Thanks for all of the help guys!
I'll get stuck into them over the coming weeks and let you know the results.
Regards
Greg
|
|
|
