| [ Total Views: 1132 | Total Replies: 27 | Thread Id: 105961 ] |
|
|
 Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 5th, 2014 at 01:17 PM |
|
|
Type 3 power issues
Hi guys, I have a type 3 wagon, automatic.
I had a problem a few months ago when the brakes failed after what felt like the brakes sticking on when getting on the highway... So I replaced all
the rubber brake lines and the master cylinder and that sorted the brakes out... Now I don't drive it very often so I thought id get it out and take
it for a run up the street before we took it to the vw show on sunday, what I found was it doing exactly the same thing when I was driving up a long
hill under load (like the ramp onto the highway) . by about half way up the hill, it just starts losing power, not like the normal VW goes up hills
slow power! by the time I got to the top of the hill the car was barely moving... it seems to drive around on the flat ok when not put under too much
load for a long period of time. Any ideas?? 1641cc twin carb.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on May 5th, 2014 at 05:09 PM |
|
|
What dizzy do you have? 009 or vacuum advance?
"If at first you don't succeed, skydiving is not for you." - Anonymous  |
|
|
BRUTUS
A.k.a.: et tu, Brute
Officially Full-On Dubber
Posts: 255
Threads: 17
Registered: February 8th, 2006
Member Is Offline
Location: Brutus has retyred
Theme: UltimaBB Pro Grey
Mood: ACE 30 FOR SALE!
|
| posted on May 5th, 2014 at 05:12 PM |
|
|
The auto trans is either worn out, or doesn't have enough ATF in it.
ACE 30 & 40 oils: specifically engineered for your Air Cooled VW
delivered (free del.) throughout Yarra Valley / Ranges, & Gippsland areas. Also ACE 20, 50 & 90.
FOR SALE: ACE 30, 40 etc. Oil formulations & Trade-names.
|
|
|
20bkombi
Wolfsburg Wizard
Posts: 597
Threads: 26
Registered: March 2nd, 2009
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 5th, 2014 at 08:44 PM |
|
|
Sounds like a fuel issue. Fuel pump rod worn. Fuel filter??
You'll work if out.
AARON'S SPEED SHIFT AUTOS
Specialising in Vw automatic transmissions, differentials and torque converters
Stock or modified to suit your application (street, drag, off road)
Ph 0402 233 027
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on May 6th, 2014 at 07:37 AM |
|
|
so if you maintain it under load, at the same load after a while it will start to loose power?
Does sound like its draining the fuel bowls. You have a stash of fuel to last a little while under load, then it begins to run out while the pump
plays catch up.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 08:03 AM |
|
|
That's right Chris... But it doesn't start to pop,fart and miss like it's running out of fuel. It just gets slower and slower until it's almost
stopped.... You can slip it into neutral and it will free rev just fine.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 10:41 AM |
|
|
Checked the ATF and it's fine and clean... I'll check fuel supply next. I think I've got another pump here, I replaced the fuel filter only about 6
months ago and haven't really driven it.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 11:08 AM |
|
|
Oh and the dizzy is a 009.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 6th, 2014 at 11:12 AM |
|
|
Was the gearbox kicking down to second gear or was it staying in 3rd gear up the hill ???
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 12:27 PM |
|
|
Gear box was only in 2nd by the the Time I started going up the hill.... I took it for another test drive after replacing the fuel pump and got the
same again .. But I noticed the more I drove it, it started piling to the left then got really hard to turn right ... Them the brakes went again as I
got home. So I've found the front left caliper is stuck on and not returning. You push the pedal once and it stays on making everything so hot I
could barely touch the wheel not could I turn it. I cracked the bleed nipple in order to release it but it didn't budge. The fluid was dead cold?? I
then pried the caliper off the disk and spun it freely, then I applied the brakes and it's locked up again. Mc is new, so are the rubber lines. One
leaning towards seized caliper but that to me doesn't explain the brakes going to the floor?
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 6th, 2014 at 02:33 PM |
|
|
Yep sounds like you need to pull the calipers off and apart or get new ones
You might be able to get away with pulling them apart and freeing up the pistons giving it all a good clean use rubber grease when re
assembling
make sure you get a solid bit of wire like coat hanger and push it through the fluid galliers as they tend to block up with sludge
The other question is did you bleed the brakes correctly when replacing the master cyclinder and hoses ??
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 02:37 PM |
|
|
Yeah, they bled up fine. But then again if there was a problem with the caliper all along then maybe not. They worked fine until I made the car really
work to get up a hill.... Another question, late type 3 calipers? Mick motors don't have them, are they hard to get? Are they not the same as late
beetle ones?
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 6th, 2014 at 02:48 PM |
|
|
it could have bleed Ok but the psiton dont move very common
yep extreamly hard to find different size to all others
thats why i said strip and rebuild local brake shop may have seals ??? or the old ones usually work if you dont stuff them getting them
apart
there is the seal on the piston and 4 small O Rings between the caliper halfs square section from memory
|
|
|
BRUTUS
A.k.a.: et tu, Brute
Officially Full-On Dubber
Posts: 255
Threads: 17
Registered: February 8th, 2006
Member Is Offline
Location: Brutus has retyred
Theme: UltimaBB Pro Grey
Mood: ACE 30 FOR SALE!
|
| posted on May 6th, 2014 at 02:51 PM |
|
|
Earlier ~68? to 70 are the smaller callipers (1 bleed valve)(different to Beetle calliper, I think).
71 - 73 are much larger callipers (2 bleed valves), same as Type 4 car of the same era, apparently. We obtained the earlier type new a few years ago,
but had to get the larger/later ones re-built more recently (quite successfully), as could not buy new ones at the time.
Have had both types professionally re-co'ed over the years.
ACE 30 & 40 oils: specifically engineered for your Air Cooled VW
delivered (free del.) throughout Yarra Valley / Ranges, & Gippsland areas. Also ACE 20, 50 & 90.
FOR SALE: ACE 30, 40 etc. Oil formulations & Trade-names.
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 02:59 PM |
|
|
Shite, might have to look into that then.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 03:28 PM |
|
|
Do you remember what it cost?? I've just had a quote for about $300 worst case... If the pistons need replacing. If not around $220.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
OZ Towdster
A.k.a.: Andrew Westwood
Custom Title Time!
Keen to finish some projects
Posts: 1921
Threads: 132
Registered: December 7th, 2003
Member Is Offline
Location: Alexandra Hills Brisbane QLD
Theme: UltimaBB Pro Yellow
Mood: Having fun in our great land
|
| posted on May 6th, 2014 at 06:03 PM |
|
|
Thats cheap even at the $300 , my landcruiser calipers we're that each !!!!!!!!!!
Also keep in mind that these old rides like a REGULAR IE ONCE A WEEK drive , not once every six months Mick , and you will have far LESS break downs
as everything is being used and not seizing up .
Yes i realise that you are selling it , but your never gunna sell it while it's a unreliable and or if you do ,you'll be coping abusive phone calls
for the next year from the new owner .
Do you also realise that modern day pump fuels are no better than vinigar after about a month , so don't expect old fuel to run as it should either
Don't let body work get in the way of real suspension travel
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on May 6th, 2014 at 08:26 PM |
|
|
2 questions.
has your brake pedal push rod got enough play, no play can cause the brakes to build pressure and forcing then to stay on.
the other is, if its actually lacking power and brakes are sorted, when did you last use up all the fuel? unleaded 91 goes off in weeks to few months
max and will run the engine like crap if, not at all.
Had this happen personally few times. Not like the fuels of the early 90s and prior, will be just as good 10 years later! 21 years later in my
brother's GT lol.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
tweety
Wolfsburg Wizard
Posts: 460
Threads: 68
Registered: February 26th, 2011
Member Is Offline
Location: Strathbogie Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 6th, 2014 at 10:36 PM |
|
|
jUST FOR YOUR INFO IT IS COMMON KNOWLEDGE THAT THE AUTO TRANS FLUID SHOULD BE A LITTLE OVERFILLED.
about 2-3mm. When I climb my driveway which is a little steep, if the gears slip a little its time to put in about 300mm of fluid due to leakage
which is common.. Better than a gauge anyday.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 7th, 2014 at 07:26 AM |
|
|
| Quote: |
has your brake pedal push rod got enough play, no play can cause the brakes to build pressure and forcing then to stay on.
|
YES good point you changed the master cyclinder is the correct free play there on the pedal
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 7th, 2014 at 07:40 AM |
|
|
Well, it did the same thing before I replaced the master cylinder so I'm leaning more towards the caliper being rooted.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on May 7th, 2014 at 01:18 PM |
|
|
Do you have the larger callipers? (twin pin) or the earlier single pin, there are 2 different size discs...
"If at first you don't succeed, skydiving is not for you." - Anonymous |
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 7th, 2014 at 01:24 PM |
|
|
Later twin pin, I've checked the free play in the pedal... theres about 15mm of free play before it even starts to engage the MC. I'm confident its
the caliper on that side.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 7th, 2014 at 02:00 PM |
|
|
Pull them apart carefully you may get away re using the seals if they dont get damaged getting them out
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on May 11th, 2014 at 10:15 AM |
|
|
If the calipers are jamming on, the seals are more than likely to be the issue. they can go hard over the life of a car, normally from lack of fluid
changes.
calipers pistons return a fraction of a mm to release the pads, and that it entirely relied on by the flexing of the pistons seals. Seals go hard,
pistons do not return back and the brakes drag.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 15th, 2014 at 05:50 PM |
|
|
Right, so I got the calipers overhauld.. one was seized, the other was just old. Fixed my brakes but she still wont drive up the hill! turns out it
was 2 separate issues all along... we are pretty confident its a fuel supply issue but where?? I have replaced the fuel pump, filter and all the
rubber fuel lines... its like the fuel bowls are getting sucked dry. I've checked the needle and seats, they are not leaking nor are they sticky.
Anyone have any advise on where to look next?? yes it does have a tank of fairly old fuel in it but I only use 98 and im sure if it was shitty fuel it
wouldn't just lose power and stall under load, I would think it would just run like shit all the time.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 15th, 2014 at 06:55 PM |
|
|
only one way to FIX a fuel issue
start at the front
Pull tank and clean including filter fill with soapy water and nuts n bolts to remove any internal dirt n crud
check the vent line to see if tank can breath may be blocked
replace rubber flex lines with quality German tubing
blow main fuel line to remove blockages no kinks in fuel lines
pull tops of carbies after start up and idle to check fuel levels in bowl
check fuel pump pressure should be 5 lbs of so
|
|
|
FROSTY
Insano Dub Head
Posts: 744
Threads: 65
Registered: May 11th, 2009
Member Is Offline
Location: Palm Beach Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 15th, 2014 at 07:04 PM |
|
|
I have a set of carbs that were taken off a 71 square Auto running perfectly if you want to try?
|
|
|
