| [ Total Views: 1813 | Total Replies: 12 | Thread Id: 106068 ] |
|
|
 thepie
Casual Dubber
Posts: 40
Threads: 22
Registered: August 14th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 15th, 2014 at 05:51 PM |
|
|
Rear hub removal
Hi all , looking for help , advice , just removed the 36mm nut from rear hub,and trying to remove the hub , with not much luck it seem to be stuck !!!
What's the best way to remove it without a puller ? Or the best place to buy or borrow one , I'm based in canberra
Cheers Dave
|
|
|
bug68m
Commited Dubber
Posts: 55
Threads: 15
Registered: May 20th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 15th, 2014 at 09:17 PM |
|
|
Put the nut back on but don't tighten all the way up leave about 1/2 a turn loose put the split pin back in so it won't come off and go for a good
hard drive around the block and check to see if it has come loose good luck best way is with a puller
|
|
|
Aussie Dubbin
Fahrvergnugen
Posts: 895
Threads: 90
Registered: July 21st, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 15th, 2014 at 10:40 PM |
|
|
Are your shoes bound up?
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 15th, 2014 at 10:55 PM |
|
|
back the brake shoes OFF
|
|
|
Shuffs
Commited Dubber
Posts: 50
Threads: 3
Registered: August 20th, 2010
Member Is Offline
Theme: UltimaBB Pro Purple
|
| posted on May 16th, 2014 at 08:24 AM |
|
|
| Quote: | Originally
posted by vw54
back the brake shoes OFF
|
I would say'THIS' also,or is not something simple,like the hand brake being on?
|
|
|
thepie
Casual Dubber
Posts: 40
Threads: 22
Registered: August 14th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 16th, 2014 at 09:15 AM |
|
|
Thanks for advice , brake adjusters backed right off & handbrake off , hubs roll freely , I'll have to invest in a puller I think , anyone know
best place to get one ?
|
|
|
STIDUB
Custom Title Time!
Over it.
Posts: 1497
Threads: 57
Registered: June 23rd, 2008
Member Is Offline
Location: Where else but QLD :)
Theme: UltimaBB Pro Blue
Mood: Worn out, for no benefit.
|
| posted on May 16th, 2014 at 09:35 AM |
|
|
nylon/rubber hammer, give it a few taps on opposing faces & a spray of your choice of lube wd40/inox/penetrene etc should get it...
Volkswagen Drivers Club of Queensland - member 
STIDUB - yep its still a work in progress
Vwdcq club car racing/ and crashing while my bug isn't finished.
The above are personal views, no more, no less |
|
|
vduboy
Insano Dub Head
Posts: 702
Threads: 41
Registered: October 6th, 2012
Member Is Offline
Theme: UltimaBB Streamlined2
Mood: Dying to get more buggy building time..
|
| posted on May 18th, 2014 at 09:01 PM |
|
|
Bolt the wheel back on and give it a few opposing boots, failing that puller would be better.
It will all be OK in the end, if it's not OK it's not the end!
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 19th, 2014 at 07:28 AM |
|
|
Yes as per above
Put the wheel back on but with 3 bolts and have it so it ratttles Make sure you have a good jack stand under the car and also a temporary jack as
well
then use the wheel as a rattle to remove the brake drum rock from side to side
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on May 19th, 2014 at 07:41 AM |
|
|
Try using a piece of soft metal like brass against the end of the axle, then whack this with a hammer
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on May 19th, 2014 at 10:32 AM |
|
|
Beaware you can bunell the bearing if you hit the axel to hard, all the force is directed into the bearing, this is why a puller is the correct
method, even a three jaw puller will work in most situations. you could hire one for a couple of hours
|
|
|
thepie
Casual Dubber
Posts: 40
Threads: 22
Registered: August 14th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 19th, 2014 at 12:21 PM |
|
|
Where would be best place to hire one from ?
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on May 20th, 2014 at 01:32 PM |
|
|
Call up a tool hire place, make sure you get one big enough, do not apply to much pressure on the od of the drum.
|
|
|
