| [ Total Views: 742 | Total Replies: 7 | Thread Id: 107432 ] |
|
|
 baja_01
Slammed & Awesome Dubber
Posts: 84
Threads: 35
Registered: July 2nd, 2009
Member Is Offline
Location: Maitland, NSW
Theme: XMBX Pro Green
|
 posted on October 19th, 2014 at 01:16 PM |
|
|
Weird End play?
Hi All
Just thought I'd adjust the end play on my new motor after being run for a couple of months. Measured it at about 41thou without shims. Okay put in 3
shims 37thou thick, put flywheel on without seal. All measured spot on. Flywheel off, seal fitted, no endplay?? Fitted seal further in and still the
same. No problems prior just too much play. What gives? I have noticed two of my seals look slightly different. One the inner lip sits slightly in
from edge more than the other.
BTW Using Elring seals and the same CroMo F/W.
The seals
[img] [/img]
[img] [/img]
|
|
|
bug68m
Commited Dubber
Posts: 55
Threads: 15
Registered: May 20th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 19th, 2014 at 08:11 PM |
|
|
You just need to tap the seal in a bit further I had the same problem you would be surprised at the difference between brands of seals I just fitted
one never re checked the end play
Then when a oil leak started at the rear main I noticed there was no end play pulled the motor and found the seal was cooked due to rubbing on the fly
wheel
As was not tapped in far enough the radius on the fly wheel was touching the inner lip of the seal
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on October 19th, 2014 at 09:32 PM |
|
|
Yea, peps think the seal sits flush with the casing face but actually the seal needs to bottom out on the cases seal recess.
madness is in the eye of the beholder  |
|
|
baja_01
Slammed & Awesome Dubber
Posts: 84
Threads: 35
Registered: July 2nd, 2009
Member Is Offline
Location: Maitland, NSW
Theme: XMBX Pro Green
|
| posted on October 20th, 2014 at 10:40 AM |
|
|
Yep tried with the seal pushed right in. Went to a bearing supply today and found a seal 2mm narrower IE: 70x90x8. Has anyone tried one of these?
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on October 20th, 2014 at 04:12 PM |
|
|
It is a good idea to install the seal using a seal installation tool the is pulled using the gland nut, does not damage the seal and keeps it square,
depth will depend on raduis on the flywheel and other machining variables, i have fitted quite a few seals flush with the case without an issue.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on October 20th, 2014 at 11:27 PM |
|
|
So you aren't using a std flywheel by the CroMo mention?
Do you have a std one to compared to as VW60 could be onto something here as if the flywheel spigot isn't tall enough of radiused like the std one
then this could well be the issue.
madness is in the eye of the beholder |
|
|
baja_01
Slammed & Awesome Dubber
Posts: 84
Threads: 35
Registered: July 2nd, 2009
Member Is Offline
Location: Maitland, NSW
Theme: XMBX Pro Green
|
| posted on October 21st, 2014 at 07:20 AM |
|
|
Yes I have a standard F/W to check against. This is the thing, the CroMoly one has been run before without any issues. Seems like there is an updated
style seal around from Elring?? I'm going to do some measuring between F/W's and I'd say get the CroMo one machined.........
|
|
|
fish26
A.k.a.: benito
Fahrvergnugen
Posts: 903
Threads: 38
Registered: July 13th, 2007
Member Is Offline
Location: sydney
Theme: UltimaBB Pro Grey
Mood: Ken awesome
|
| posted on October 21st, 2014 at 08:54 AM |
|
|
The sealing lip has enough flexibility to allow slight machining tolerances between flywheels, I always polish the radius on the flywheel, oil the
seal, Permatex Aviation on seal/case edge, could your problem be too much grease between the shims?
bitten by the bug..........several times
|
|
|
