| [ Total Views: 1356 | Total Replies: 21 | Thread Id: 112219 ] |
|
|
 beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 8th, 2017 at 01:07 AM |
|
|
Ball joints loose in L bug track control arms
I had a wheel alignment done on my 2 bolt L bug, and the wheel alignment bloke found the caster was a bit out (after front end prangs over the years I
reckon). As there is no real castor adjustment, we got another set of track control arms, and he has bent them forwards slightly to correct the
caster.
When he went to fit the new set of ball joints that I had purchased, he found they are too loose - they just slip in. I rang the shop where I
purchased both the arms and the ball joints, and they checked a few other arms and found some were not as bad, but still loose.
They chased around and found that over-size ball joints used to be available, but are no longer. Has anyone else had this problem, and how did they
overcome it?
From your ole' mate Jeff
|
|
|
vduboy
Insano Dub Head
Posts: 702
Threads: 41
Registered: October 6th, 2012
Member Is Offline
Theme: UltimaBB Streamlined2
Mood: Dying to get more buggy building time..
|
| posted on March 8th, 2017 at 10:17 AM |
|
|
Failing finding some oversize ball joints, you could get them tigged up and re machined, but authorities frown on welding of suspension components..
It will all be OK in the end, if it's not OK it's not the end!
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 8th, 2017 at 12:11 PM |
|
|
Rather than the ball joints are the control arms flogged out?
Futue te ipsum!!!
|
|
|
karmann141
Wolfsburg Wizard
Posts: 485
Threads: 48
Registered: August 27th, 2009
Member Is Offline
Location: Carindale - Brisbane
Theme: UltimaBB Pro Blue
|
| posted on March 8th, 2017 at 12:48 PM |
|
|
| Quote: | Originally
posted by vduboy
Failing finding some oversize ball joints, you could get them tigged up and re machined, but authorities frown on welding of suspension components..
|
Also frown on bending suspension components - may as well go the whole hog.
I had the same problem when having a wheel alignment done - they placed shims on 1 side to get the caster back in spec. Unfortunately the monkeys
didn't put the cotter pin back in the castellated nut. Luckily we were only doing low speed teaching my daughter to drive, when the suspension
collapsed. Could have been killed if it happened the previous night doing 100 kph doing night-time practice.
https://forums.aussieveedubbers.com/viewtopic.php?tid=104658&page=1#pid98...
1961 K Ghia - Porsche 5 sp, EJ20T, Brembo's, Dble A arm susp
1974 L Bug - Porsche 944 brakes, Boxster 16's
1974 Bay Camper - EJ20, twin radiators, Boxster 16x7's
Half Beetle trailer with Boxster 16x7's
2011 Tiguan TDI 4Motion
2010 LR Discovery 4 TDV
|
|
|
mackaymanx
A.k.a.: Brent
Custom Title Time!
Posts: 1611
Threads: 97
Registered: January 12th, 2006
Member Is Offline
Location: Mackay.QLD
Theme: UltimaBB Pro Blue
Mood: Brad'ed Off 
|
| posted on March 8th, 2017 at 05:39 PM |
|
|
Had this same problem many years ago and the shop welded around the outside of the socket which shrank it down. Don't know if this would suit you
though.
Quote of the week
"Do I wish to send them to you again, nope, no interest can't be bothered really, to much hassle for little or no return."
 |
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on March 8th, 2017 at 06:29 PM |
|
|
They're a welded construction anyway so as long as a competent welder does the job it won't matter. I'd say source some thick wall tube that the
joint will press into snugly. Then cut the old hoops off and weld the section of pipe on.
madness is in the eye of the beholder  |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on March 8th, 2017 at 08:44 PM |
|
|
You could machine a thin walled flanged shim, work out how loose they are and calculate the wall thickness required, no need to weld, this would
present other problems as you do not know the material or the welding code for the material, also it would require machining after it was welded to
give you a true bore, the shim would be hard to make but is not impossible, then press it in.
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 8th, 2017 at 11:14 PM |
|
|
I got the arms from VVWS, and I have talked to them about it - they measured 2 other arms they had there - and while they were both slightly smaller,
they were both still too big for the ball joints. They chased around and found that Tooleys used to have oversize ball joints available about 8 years
ago, but they no longer do. Surely mackaymanx and I are not the only people who have had this problem.
vwo6o, the ball joints measure 36.88mm, and the inside of the hole in the arms is 37.28mm, so a shim would only need to make up 0.4mm, so a wall
thickness of 0.2mm - I don't think it would really be feasible.
My wheel alignment bloke suggested welding around the outside of the socket as mackaymanx had done, and that seems like the way we will probably go at
this stage. As mentioned, the arms are welded together from new anyway, so I don't see that as being a problem.
I will let you know how we go.
From your ole' mate Jeff
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on March 9th, 2017 at 08:10 AM |
|
|
Yes you would be able to turn that thickness, as I said it would take a fair amount of experience, keep in mind that it is illegal to weld suspension
components yourself and would take an engineer to approve if you did, on the other hand shrinking it might work, have you thought about heating it up
and quenching, just remember the od will have to reduce by .4MM to get to the same size as the ball joint before the interference is achieved, if you
do not weld it all the way around you will end up with a bore that is not round.
|
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on March 9th, 2017 at 08:29 AM |
|
|
How about Loctite 660 ?
http://www.loctite.com.au/3320_AUE_HTML.htm?nodeid=8802627715073
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on March 9th, 2017 at 05:33 PM |
|
|
I think VVDS has found some arms for you
I think a weld bead and quench would do the job weld n quench a bit at a time that will pull it in
|
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on March 9th, 2017 at 05:57 PM |
|
|
Followed up with heat-treating and/or shot-peening to relieve stresses ?
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 10th, 2017 at 01:38 AM |
|
|
| Quote: | Originally
posted by vw54
I think VVDS has found some arms for you
|
When I talked to Michael and we measured them, they were slightly smaller than the first ones they sent me, but still bigger than the ball joints. We
will see whether we can do anything with the first set first.
From your ole' mate Jeff
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on March 10th, 2017 at 05:24 PM |
|
|
It makes the old 3 bolt units look good.
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on March 10th, 2017 at 08:30 PM |
|
|
You may not think much of this idea-but it was taught to me when I was an apprentice mechanic in my second year-yes a very long time back.
If there is only a few thou in it-knock all the flux from a small arc welding rod,set the amps what you would normally use for about 3mm plate-then
poke the rod inside the opening and quickly move it around in circles touching the opening and making sure it doesn't weld itself to the opening.
This will leave a lot of small welded lumps all over the opening.If there are large ones,quick clean with a dye grinder.I was taught to do this to
Valiant tailshaft uni joint bosses.
I used this method recently on some VW link pin bushes.Wasn't happy with one of them,so pressed it out and did it again.Ended up really firm.You can
tell how tight they are when pressing them in.
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 12th, 2017 at 01:27 AM |
|
|
We have decided to go with the weld & shrink method at this stage.
Out of interest, here is a video of how loose the ball joints are in the arms. Looking at the arms, there appears to be only 2 lots of spline marks
from previous ball joints, so you wouldn't think they would be that worn in this location.
https://www.youtube.com/watch?v=ftWBmpVO60w
From your ole' mate Jeff
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 12th, 2017 at 08:19 AM |
|
|
Jeff - nothing on SBO?
I am sure the were some articles on this.
Thought I had this issue but was resolved with a new arm?
Futue te ipsum!!!
|
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on March 12th, 2017 at 10:12 AM |
|
|
If the clearances are closer to .010" or more, then a possibility would be to ream it out slightly bigger, then fit a crankshaft speedi-sleeve before
reaming it down to spec size if needed.
I'm with Greg on the shot-peening too........
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 12th, 2017 at 10:27 AM |
|
|
Barry, I did post up on the SBO FB page, but the main response was from yanks who mainly recommended welding the ball joint into the arm.
I didn't try the SBO forum. I will give it a search if I get time this evening.
From your ole' mate Jeff
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 12th, 2017 at 12:26 PM |
|
|
contact Joel
I'm sure he will have an answer
I'm seeing Holzl this arvo - i will ash as well
Futue te ipsum!!!
|
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 14th, 2017 at 09:02 PM |
|
|
Well, Stewart welded the ends of the track control arms and got the ball joints fitting perfectly. He will fit them and do the wheel alignment while I
am away until the end of next week - March 24th
From your ole' mate Jeff
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 15th, 2017 at 07:09 PM |
|
|
Futue te ipsum!!!
|
|
|
