| [ Total Views: 360 | Total Replies: 4 | Thread Id: 24566 ] |
|
|
 Beetle bailey
A.k.a.: Beetle Bailey
Commited Dubber
Posts: 54
Threads: 33
Registered: November 24th, 2003
Member Is Offline
Location: Ellenbrook WA
Theme: UltimaBB Streamlined2
Mood: Hopeful
|
| posted on June 18th, 2004 at 07:26 AM |
|
|
Adjusting generator belt on type 3
My generator belt is a bit loose.
How do I tighten it up and are there any special tools required?
Thanks
Beetle
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 18th, 2004 at 08:09 AM |
|
|
Its basicly the same as a Beetle only a little more tricky as there isnt much space in there great if you have small finger n hands.
its a 21mm nut to be undone and remove 1 shim from the center and refit the pully.
the belt should deflect about 13mm to have the correct tension.
|
|
|
PurpleT3
Fahrvergnugen
Posts: 880
Threads: 55
Registered: April 8th, 2003
Member Is Offline
Location: Knox, Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: knackered
|
| posted on June 18th, 2004 at 08:30 AM |
|
|
You need two spanners, one to turn the 21mm nut and one to hold the spacer under the nut which is shaped with with two flat sides to allow a spanner
to grab it. The main problem is that the spacer is inside the pulley and access is a pain in the ass. You will need to find a very skinny spanner or
make up a special tool to do it.
As 54 said, remove the shim from between the pulley halves to tighten the belt. The shim you remove MUST be put under the spacer, you must always
have the same total no. of shims, do not take the shim out and dispose of it.
Ain't nothin' like the wind in your hair.
|
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
| posted on June 18th, 2004 at 09:42 AM |
|
|
And don't drop anything down inside the shroud!!!
Kruizin Kol
|
|
|
PurpleT3
Fahrvergnugen
Posts: 880
Threads: 55
Registered: April 8th, 2003
Member Is Offline
Location: Knox, Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: knackered
|
| posted on June 18th, 2004 at 10:34 AM |
|
|
Amen to that. Before starting, go to your FLAPS and buy one those magnetic extendo pick up tools in case you do drop something in the shround. Also
make sure you have band aids, cos you will skin your knuckles!
Ain't nothin' like the wind in your hair.
|
|
|
Beetle bailey
A.k.a.: Beetle Bailey
Commited Dubber
Posts: 54
Threads: 33
Registered: November 24th, 2003
Member Is Offline
Location: Ellenbrook WA
Theme: UltimaBB Streamlined2
Mood: Hopeful
|
| posted on June 18th, 2004 at 01:30 PM |
|
|
Thanks for your help everyone.
Sounds like a painful exercise but I will give it a go
Ken
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 18th, 2004 at 08:17 PM |
|
|
Or u can just shove a piece of Rag down into the fan housing surround... stops the washers getting LOST
|
|
|
