| [ Total Views: 1048 | Total Replies: 7 | Thread Id: 51025 ] |
|
|
 urban_myth
A.k.a.: Jason
Officially Full-On Dubber
Posts: 354
Threads: 60
Registered: January 6th, 2005
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 16th, 2006 at 05:10 PM |
|
|
Starting an engine which has been sitting for several years
I recently bought a '75 1600 twin port with low k's that has been sitting for around for 6 years. Is there anything I should do before starting it
up? I'm changing the oil and rear main seal. I'm not worried about water as it was stored undercover. I'll be adjusting the valves and changing the
rocker cover gaskets as well. Will the carby need a kit through it?
|
|
|
Anthiron
A.k.a.: Nicko McKay
Compulsive Aussie Vee Dubber
The Baja Rejuvenation Begins
Posts: 4936
Threads: 310
Registered: October 1st, 2003
Member Is Offline
Location: Buderim QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Hell hath no fury like a womans scorn for sega.
|
| posted on April 16th, 2006 at 05:13 PM |
|
|
squirt a little oil down the spark plug holes and turn it over by hand a few times to get things lubed up.
62/60 model bug eye baja bug, (Full Build in Progress)
1974 Chevrolet Luv
1970 MK2 Ford Cortina GT
1979 Yamaha RX125 Two Stroke tracker project.
2004 Harley Davidson Sportster XL Custom
|
|
|
mackaymanx
A.k.a.: Brent
Custom Title Time!
Posts: 1611
Threads: 97
Registered: January 12th, 2006
Member Is Offline
Location: Mackay.QLD
Theme: UltimaBB Pro Blue
Mood: Brad'ed Off 
|
| posted on April 16th, 2006 at 05:37 PM |
|
|
Turn it over without plugs until the oil presure comes up.Carb is a bit hit and miss, put some fuel in it to soak into the gaskets awhile before start
up.After 6 years you might expect a bit a scale built up to have flaked off the inside of the carby ( depends on how clean the fuel has been), could
block the jets. A kit would probably be a good idea, acc and choke diaphrams are likely to be in not the best shape.
Quote of the week
"Do I wish to send them to you again, nope, no interest can't be bothered really, to much hassle for little or no return."
 |
|
|
tassupervee
A.k.a.: Knob Jockey
Custom Title Time!
That really hurts doesnt it!
Posts: 1171
Threads: 25
Registered: September 21st, 2003
Member Is Offline
Location: Huon Valley SouthernTasmania
Theme: UltimaBB Psyche Blue
Mood: Moody!
|
| posted on April 16th, 2006 at 07:33 PM |
|
|
Yer like they said.
If fuel was left in the carb, as it evaporates, it can ove time leave a goo in the carb that can make you day rather miserable.
Might be wise to drain the fuel tank as well and fush out the lines.
For mine, id simply give it a try, worst case scenario, it wont run and you have to lift the top off the carb and clean it.
Have fun.
L8tr
E
Im not a complete idiot, quite a few parts are missing....
|
|
|
urban_myth
A.k.a.: Jason
Officially Full-On Dubber
Posts: 354
Threads: 60
Registered: January 6th, 2005
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 16th, 2006 at 07:47 PM |
|
|
The car its going in i've been driving daily, so the petrol tank and lines are fine, i'm just replacing the engine with this one. The guy I bought
it off said it had 75,000 original k's. You could tell engine hadnt been cleaned down for the sale, but it didnt have any oil leaks, just a little
build up of road grime. It should go well.
|
|
|
mackaymanx
A.k.a.: Brent
Custom Title Time!
Posts: 1611
Threads: 97
Registered: January 12th, 2006
Member Is Offline
Location: Mackay.QLD
Theme: UltimaBB Pro Blue
Mood: Brad'ed Off
|
| posted on April 19th, 2006 at 11:40 AM |
|
|
If you are putting this straight in you should retorque as many case bolts that you can get to, and especially the head bolts
Quote of the week
"Do I wish to send them to you again, nope, no interest can't be bothered really, to much hassle for little or no return."
|
|
|
VWCOOL
23 Windows of Awesome
Posts: 5158
Threads: 235
Registered: June 19th, 2003
Member Is Offline
Location: In the shed... Lake Macquarie NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: happy to help
|
| posted on April 19th, 2006 at 02:40 PM |
|
|
NO DON'T TOUCH THE CASE BOLTS as it may nip up the bearings and sieze the engine
Pay your debts, CxxT
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on April 20th, 2006 at 07:35 AM |
|
|
yes pull the plugs and turn it over by hand a few times with some oil down each plug hole and to make sure it turns free.
Take out the oil pressure sender bulb and spin the engine over on the starter to get up oil pressure
put the plugs back in and hit the stater... with some " Start yar Bastard " down the carby to make it kick easier
|
|
|
