| [ Total Views: 1189 | Total Replies: 7 | Thread Id: 56214 ] |
|
|
 seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 8th, 2006 at 02:12 AM |
|
|
Subaru turbo headers !
has any one fitted a set of these after market turbo headers to there turbo motor .The weight savings is a lot , quality .
Looking for that special lady : PM me for coffee & cake
|
|
|
71superbug
Custom Title Time!
The Itch Itcher
Posts: 1184
Threads: 72
Registered: May 20th, 2004
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: Subified
|
| posted on September 8th, 2006 at 03:06 AM |
|
|
best place to ask neil would be a subaru forum, last time i had a look there was plenty of information as to which was better with most gains .etc
i imagine it would be very brand dependant as to which is the most effective.
Anthony
|
|
|
ricola
Wolfsburg Wizard
Posts: 437
Threads: 9
Registered: February 5th, 2003
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 8th, 2006 at 06:30 AM |
|
|
Good power gains to be had, but there are problems with them cracking if they don't have flexi joints (much more expensive) and they all look pretty
deep, will lose the rumble if you go for all out power with equal length one.
I've heard a basic match porting job on the standard headers can give up to 30bhp which is the way I'd go..
Rich
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on September 8th, 2006 at 08:57 AM |
|
|
Hi
Im pretty sure that the Rigolis still use a modified stock header on their drag car.
Im pretty sure from what I have gathered is that the headers are usually larger in diameter, that will move the powerband up in the rpm range.
I might change the up pipe, there seems to be gains in that area with no down side.
Steve
|
|
|
gull
Wolfsburg Wizard
Posts: 446
Threads: 34
Registered: June 30th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 8th, 2006 at 11:14 AM |
|
|
I made my own for the n/a trike form 2" ss tube bends .Lots of work but there was power gains
I am getting a set today for the dragon .Its a weight thing for me , I dont care about the grumble note .
|
|
|
ricola
Wolfsburg Wizard
Posts: 437
Threads: 9
Registered: February 5th, 2003
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 9th, 2006 at 05:33 AM |
|
|
http://www.germanlook.com/Forums/showthread.php?t=7848
shows how deep they are!
Rich
|
|
|
boof2332
Custom Title Time!
Posts: 1210
Threads: 120
Registered: May 10th, 2004
Member Is Offline
Location: Beecroft Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Sympathetic
|
| posted on September 13th, 2006 at 10:27 PM |
|
|
I got a power up pipe on my car, however I made one for the splitty that is a little shorter than normal, with a different angle to fit under the
tank. This is where there is alot of difference in port size. big to small to big again, with no smooth transition. I looked at all the ports on the
headers and they were already matched.
Matt
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 13th, 2006 at 11:59 PM |
|
|
The ss headers are low , so I just have to fit them to project X 
Looking for that special lady : PM me for coffee & cake
|
|
|
