| [ Total Views: 1563 | Total Replies: 11 | Thread Id: 63376 ] |
|
|
 72RSbug
Officially Full-On Dubber
Posts: 266
Threads: 49
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 25th, 2007 at 05:05 PM |
|
|
Quick help from EJ20 guys please
The ECU relay is malfunctioning on my JDM EJ20TT and I need to replace it.
Problem: have no idea were to get JDM parts like this(I live in Belgium)
Does anyone know if other EJ20 engines use the same relay as this one? Can you guys check your's please?
the folllowing is written on the relay:
RELAY 2M
25229AA001
MR5A414A1K 12V
60611V JIDECO
If I can replace this part my engine should work again finally
|
|
|
ratbug
A.k.a.: Andrew Todd
Wolfsburg Wizard
aka toddy101
Posts: 439
Threads: 30
Registered: January 14th, 2003
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 25th, 2007 at 06:33 PM |
|
|
Sorry I can't help you on getting a replacement, but if you get stuck and have the wiring diagrams you could replace it with two conventional
everyday relays with a little bit of rewiring.
|
|
|
72RSbug
Officially Full-On Dubber
Posts: 266
Threads: 49
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 25th, 2007 at 06:36 PM |
|
|
Don't have the wiring diagram either, I only have the ECU pinout
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on June 26th, 2007 at 09:17 AM |
|
|
| Quote: | Originally
posted by ratbug
Sorry I can't help you on getting a replacement, but if you get stuck and have the wiring diagrams you could replace it with two conventional
everyday relays with a little bit of rewiring.
|
I had the same problem and Brad gave me this advice too. Find the wiring diagram. I know it's a pain in the neck, but these relays are hard to get
over here too, even second hand. I was lucky and found one second hand for $10. Subaru charge like $110 for ONE of them.
|
|
|
ratbug
A.k.a.: Andrew Todd
Wolfsburg Wizard
aka toddy101
Posts: 439
Threads: 30
Registered: January 14th, 2003
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 26th, 2007 at 06:47 PM |
|
|
You might be able to work it out using the old coil... break her open and have a look. Two wires will be going to the coil, these will have to go to
the coil of the new relays (terminals 85 & 86). I'm guessing the other 4 wires are two sets of Normally open contacts (you can confirm by having a
look at the contacts, if there is a gap when the relay is unpowered then its normally open). Normally open contacts on an everyday automotive relay is
terminals 30 and 87. Alternatively if you can get hold of a double pole (DPxx) relay, that could do the job with just the one relay.
If you break open the case, you might even be able to clean the contacts up a bit and get it back up and running.
.
|
|
|
72RSbug
Officially Full-On Dubber
Posts: 266
Threads: 49
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 26th, 2007 at 08:57 PM |
|
|
got lucky and found one on a eurospec legacy that works.
were I'm at so far: the ECU doesn't give the negative signal to the brown relay in order to activate it but if I put a negative on it myself,the ecu
does power the spark plugs and I can get it running (badly) if I connect the fuel pump relay directly to the battery instead of the ECU powered fuel
pump relay....?
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on June 27th, 2007 at 10:04 AM |
|
|
probably, but remember the ECU switches the EFI pump on and off. still I guess that's what the pressure valve is for. also, you may get a fault code.
the fuel pump relay is green, I'd check the liberty for that too if you can still get to it.
|
|
|
72RSbug
Officially Full-On Dubber
Posts: 266
Threads: 49
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 27th, 2007 at 10:28 PM |
|
|
update: the fuel pump relay works so that's not the problem.
Discovered that the timing belt jumped 1 tooth, will put a new one on this weekend.
Could the timing belt be the cause of the ecu not powering the brown relay and fuel pump relay?
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 28th, 2007 at 12:07 AM |
|
|
no I think the issue is you inter lock from the ecu not seeing the shifter feed paulse .in sort look at the diagram you will see the wire I am talking
about
Looking for that special lady : PM me for coffee & cake
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 28th, 2007 at 12:08 AM |
|
|
I have about 40 of those relays in Perth 
Looking for that special lady : PM me for coffee & cake
|
|
|
72RSbug
Officially Full-On Dubber
Posts: 266
Threads: 49
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 28th, 2007 at 12:44 AM |
|
|
could be seagull but before I fried the loom, it was hooked up exactly the same as it is now and it worked.
I'm waiting on a diagram for my 3 plug ECU and I'll check it out, that shifter feed pulse might have cotten interrupted somehow.
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 29th, 2007 at 11:25 PM |
|
|
I have a GTB ecu if you need one
Looking for that special lady : PM me for coffee & cake
|
|
|
