| [ Total Views: 1239 | Total Replies: 7 | Thread Id: 68414 ] |
|
|
 Mowog
Learner Dubber
Posts: 16
Threads: 5
Registered: February 26th, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
Mood: Tired
|
| posted on April 5th, 2008 at 07:42 PM |
|
|
Rusted seal retaining lips and at rear window
Hi all.
I just collected a 72 1300 Beetle from a fellow forum member, which I've promised to restore if economically possible.
Apart from rust in the usual places, floorpan, bottom of front wheelarches, immediately next to the heater inlet tubes under the rear seat etc etc.
the other rust causing me concern is the bonnet lid seal & engine cover seal retaining lips are badly rusted, and either side of the rear window,
down to the air intake louvres and out to the rain gutter are fairly badly bubbled and blistered.
Can anyone please help with some advice on these problems?
I've gone through several websites, but none have listed replacement seal retainers. Are they available anywhere, & if not do I have no choice
but to replace entire panels?
Can anyone advise on how to tackle the rust at the rear window.
Thanks. Scotty.
[size=4]A pessimist is never disappointed![/size]
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on April 6th, 2008 at 08:24 AM |
|
|
those strips are rust traps anyway cos of the sealer over the joint the factory used
if ur not worried about a 100% authentic resto what i do on any bug that has rust under them is rip them off completely, grind down the welds and
either stick some weather stipping foam on there or get mexican style seals which clip onto the lip on the bonnet and decklid
this way also gives a much cleaner look too
whilst ur doing the repairs around the rear window make sure to scrape out all the expanding foam thats inside there
thats the reason it has rusted in the first place
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on April 6th, 2008 at 10:58 AM |
|
|
thats good advice..
My beetle had some small holes under the rear window rubber
My Son brazed them up for Me...
between the rear window and gutter
cut out all the rusted metal then weld new metal back in
or use putty [bog] to fill the gap...
and pull the strips off that hold the rubber seal on the bonnet and engine lid
and then replace them with Mexican look seals
vintage Vee Dub have these..
cheers
Lee
http://community.webshots.com/user/vw68autobug
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
cam070
Custom Title Time!
Posts: 1332
Threads: 53
Registered: July 25th, 2009
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Getting hands dirty stripping the bug down
|
| posted on August 11th, 2009 at 06:24 PM |
|
|
| Quote: | Originally
posted by Joel
whilst ur doing the repairs around the rear window make sure to scrape out all the expanding foam thats inside there
thats the reason it has rusted in the first place
|
Does anyone sell a rust repair panels for that section? From my experience all the later beetles rust through there due to the vent and the foam.
Also, should you replace the foam with something else afterwards? If so with what?
Doesn't it act as a barrier to sound and exhaust fumes?
|
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on August 11th, 2009 at 07:09 PM |
|
|
In regards to brazing (bronze) on any rust holes, I will give some experience here. Don't do it, if you want to fix the rust properly. The heat and
more so the flux used accelerates future rust problems. It rusts quicker than fibreglass.
|
|
|
greasykitchen
A.k.a.: Stephen
Officially Full-On Dubber
Posts: 375
Threads: 13
Registered: December 12th, 2007
Member Is Offline
Location: Torrensville, SA
Theme: UltimaBB Pro Blue
Mood: PhD recovery
|
| posted on August 11th, 2009 at 07:38 PM |
|
|
That's my old bug in the original post. I wonder if it's being restored or wrecked?
'76 Golf
 |
|
|
cam070
Custom Title Time!
Posts: 1332
Threads: 53
Registered: July 25th, 2009
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Getting hands dirty stripping the bug down
|
| posted on August 11th, 2009 at 07:42 PM |
|
|
Sorry, I wasn't asking about brazing. I was wanting to know if anyone made a c-pillar rust repair panel. Any ideas on the best way to repair this
section?
|
|
|
helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on August 11th, 2009 at 08:43 PM |
|
|
Have a look at this website Cip1
http://www2.cip1.com/
They have the seal channels as a straight length that you bend and weld to suit front or rear. I would not be surprised if they have the C pillar
sections also.
The best way to repair the section is to cut out all of the rust affected metal, weld the new section in place, and after finishing, ensure you seal
inside where the welding took place, by squirting a rust preventative on the back of the bare welds. Fish oil or body cavity wax.
|
|
|
