| [ Total Views: 965 | Total Replies: 4 | Thread Id: 76010 ] |
|
|
 Transparu
Seriously Crusin Dubber
Posts: 154
Threads: 79
Registered: February 19th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: GREAT!!
|
| posted on April 18th, 2009 at 11:55 AM |
|
|
EJ22 oil seal (and more)
Greetings all.
In 2003 I put an EJ22 into my 1982 Transporter.
The Subaru engine had done about 90,000km so I replaced the timing belt and whatever else was recommended at the time. I have been VERY happy with
the engine.
Now, 55,000km later it seems the crankshaft oil seal is leaking and needs replacement. Do people have suggestions of other items that ought to be
replaced at the same time (i.e. while I have that end of the engine in pieces)?
Thanks folks,
Dave
(Just returned from a 3,500km jaunt from Brisbane to Tocumwal, Echuca, Deniliquin, Bourke, Cobar, Lightning Ridge, Dirranbandi, Goondiwindi and home.
I really enjoyed driving the van - a camper - especially with cruise control!)
|
|
|
ratbug
A.k.a.: Andrew Todd
Wolfsburg Wizard
aka toddy101
Posts: 439
Threads: 30
Registered: January 14th, 2003
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 18th, 2009 at 12:29 PM |
|
|
Not much else in that side of the engine, you could pull the inspection plate off and reseal it with silicon, just in case that starts leaking (held
on with about 10 phillips head screws).
Did you replace the camshaft seals when you got it, these can also start leaking along with the crank seal, but they are in the front.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on April 18th, 2009 at 03:09 PM |
|
|
Dave i just got déjà vu reading that as i already got the email from SV 
is it the pulley end seal or the flywheel end seal?
there both fairly similar to replace but if its the pulley end while its off its worth checking the oil pump which is behind for leaks as well
|
|
|
Transparu
Seriously Crusin Dubber
Posts: 154
Threads: 79
Registered: February 19th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: GREAT!!
|
| posted on April 18th, 2009 at 05:58 PM |
|
|
Thanks Joel and ratbug.
Sorry, it's the timing belt end of the engine.
OK I'll look at the oil pump seal too.
Dave
|
|
|
ratbug
A.k.a.: Andrew Todd
Wolfsburg Wizard
aka toddy101
Posts: 439
Threads: 30
Registered: January 14th, 2003
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 18th, 2009 at 07:26 PM |
|
|
Ahh I thought you meant the flywheel side.
Ok well, the oil pump seal is the pulley seal. If your changing that you'd be taking the timing belt off etc etc, so i'd at the same time do the cam
shaft seals. You'd be kicking yourself if you went to all the trouble changing the oil pump seal, and then a few 1000ks later have to take it all
apart again to do the cam seals.
|
|
|
