| [ Total Views: 1278 | Total Replies: 11 | Thread Id: 76434 ] |
|
|
 gaz58t2
Slammed & Awesome Dubber
Posts: 84
Threads: 17
Registered: April 2nd, 2008
Member Is Offline
Location: Darwin
Theme: UltimaBB Pro Grey
Mood: tip top
|
| posted on May 9th, 2009 at 09:20 AM |
|
|
Adapter plate fixings
Hi Guys
Well i an currently fitting an EJ22 into my splitty
When fitting the adapter plate to engine the bottom 2 fixings are proud and will not fit to the gearbox housing
So is it best to counter sink the bolts in the adapter plate,if so were do i find these bolts (10mm x1.25 pitch)with the counter sunk heads they dont
have any in Darwin
Or is there another way to do this
Gearbox is a T1 IRS
All input would be welcome
Cheers Gaz
|
|
|
mackaymanx
A.k.a.: Brent
Custom Title Time!
Posts: 1611
Threads: 97
Registered: January 12th, 2006
Member Is Offline
Location: Mackay.QLD
Theme: UltimaBB Pro Blue
Mood: Brad'ed Off 
|
| posted on May 9th, 2009 at 11:50 AM |
|
|
From what I have found out countersunk M10x1.25 bolts are not available in Australia. My Sherman kit came with countersunk BSF bolts but I found the
fit was crap and threw them away. What I have seen done is to clearance a groove throught the engine mounts where the bolt heads foul.
Quote of the week
"Do I wish to send them to you again, nope, no interest can't be bothered really, to much hassle for little or no return."
 |
|
|
GeorgeL
Officially Full-On Dubber
Posts: 231
Threads: 11
Registered: February 5th, 2006
Member Is Offline
Location: 7200 miles off the Queensland coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 12th, 2009 at 04:07 AM |
|
|
I find it hard to believe that in an entire nation that is supposedly metrificated you don't have an outlet that can supply flat-head socket bolts.
How about this outfit: http://www.gippslandbolts.com.au/
|
|
|
ricola
Wolfsburg Wizard
Posts: 437
Threads: 9
Registered: February 5th, 2003
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 12th, 2009 at 04:10 AM |
|
|
The problem is finding them countersunk so they can be flushed in to the adapter plate.
I looked all over the place in the UK but ended up getting a small batch made up, I quickly sold them all the others to other converters...
|
|
|
GeorgeL
Officially Full-On Dubber
Posts: 231
Threads: 11
Registered: February 5th, 2006
Member Is Offline
Location: 7200 miles off the Queensland coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 12th, 2009 at 04:21 AM |
|
|
| Quote: | Originally
posted by ricola
The problem is finding them countersunk so they can be flushed in to the adapter plate.
I looked all over the place in the UK but ended up getting a small batch made up, I quickly sold them all the others to other converters...
|
Perhaps I'm misunderstanding. You're talking about these, right?
(second row, on right)
http://www.mcmaster.com/#socket-cap-screws/=1tvvav
|
|
|
gaz58t2
Slammed & Awesome Dubber
Posts: 84
Threads: 17
Registered: April 2nd, 2008
Member Is Offline
Location: Darwin
Theme: UltimaBB Pro Grey
Mood: tip top
|
| posted on May 12th, 2009 at 09:26 AM |
|
|
Proplem being it needs to be counter sunk with a fine metric thread 10 x 1.25
Not the standard 10x1.5
Think im going to go over size and get it machined and rethreaded
Thanks for the input guys
Gaz
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on May 12th, 2009 at 11:41 AM |
|
|
I cut a bit of rubber out of my banana gear box mounts and then it fitted good .
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on May 12th, 2009 at 05:05 PM |
|
|
thats all i plan on doing
|
|
|
ricola
Wolfsburg Wizard
Posts: 437
Threads: 9
Registered: February 5th, 2003
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 13th, 2009 at 07:29 AM |
|
|
No issue really on buses, but it helps a lot on bugs when you move the trans forwards, then you come up against the trans cradle, not the rubber
bush..
|
|
|
gaz58t2
Slammed & Awesome Dubber
Posts: 84
Threads: 17
Registered: April 2nd, 2008
Member Is Offline
Location: Darwin
Theme: UltimaBB Pro Grey
Mood: tip top
|
| posted on May 13th, 2009 at 08:27 AM |
|
|
Well mine is defo hitting the gearbox housing.
Im not to inclined to make clearance in the housing.
I wish it was as simple as cutting the banana rubber to get the required clearance
Will keep informed of out come as its on the jobs todo today list
Cheers Gaz
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on May 13th, 2009 at 04:06 PM |
|
|
I just have a IRS box and one of those heavy duty gear box mounts that goes around the bell housing it looks like the stock one. or are you using the
big thick L bug mounts???? and cradle??
my type
http://www.beetleracing.com/catalog/product_info.php?products_id=59
|
|
|
gaz58t2
Slammed & Awesome Dubber
Posts: 84
Threads: 17
Registered: April 2nd, 2008
Member Is Offline
Location: Darwin
Theme: UltimaBB Pro Grey
Mood: tip top
|
| posted on May 13th, 2009 at 08:27 PM |
|
|
Well all is well in Adapter plate land
Ended up using Bolts with smaller heads the ones that hold down the cast bracket for the Alternator and compressor
Then cut off the bolt lip so its 14 mm head misses the housing now just have to cut the rubber mount
Thanks guys got me thinking about the problem from a different angle
Cheers Gazza 
|
|
|
