| [ Total Views: 948 | Total Replies: 4 | Thread Id: 78038 ] |
|
|
 Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2816
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on July 26th, 2009 at 10:28 PM |
|
|
Getting a '73 back on the road
OK,
Have been right through my '73 fasty, pretty much all the running gear is new or reco'ed and entire underneath and usualy rust areas have been
cleaned and rust protected.
What do people do to protect the rear pillars? What's the best way to remove the expanded foam stuff in there, and is it best to seal off the vent
holes?
Similar with the front fresh air inlet. Is there any access into the inlet to stop it rusting inside?
This car is pretty much rust free, so I'd like to keep it that way!
Is there any service work you can do to the steering box? I assume they are grease filled, so can new grease be put in? Anyone ever pulled on
apart?
Thanks for any help!
Andy 
|
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on July 26th, 2009 at 10:57 PM |
|
|
Penrite steering box lube
The foam in the rear pillars can be aborted with a coat hanger.
http://www.penriteoil.com.au/products/classic-car-oil/steering_box_lubricant
|
|
|
Klaus
Custom Title Time!
Posts: 1439
Threads: 100
Registered: August 25th, 2004
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: Heavily modified
|
| posted on July 27th, 2009 at 06:56 PM |
|
|
"aborted " "coathanger " too funny 
with the under dash vents make sure the big rubber ring is in good condition you could even seal it up with windscreen sealant.
|
|
|
Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2816
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on July 28th, 2009 at 12:36 AM |
|
|
Thanks for the replies!
I thought the foam might be disolved with a solvent of some sort?
Klaus, I assume that is on top of that fan box? Is that easily removed to check?
|
|
|
Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2816
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on August 20th, 2009 at 11:26 PM |
|
|
Thanks again for the help. The dash has since been pulled apart to check it all out. Even removed the windscreen to check under the seals. All looked
good, and properly rust proofed.
It's so nice to have a type 3 without rust!!! (well very little anyway 
The rear pillars are still a worry, bot what foam I could out, and drain lines from the vents are not blocked and don;t leak into the pillar. Got fish
oil and tectol up inside as far as I could.
Probably still worth trying to seal up the vents in the pillar at some stage. Might not be original, but less likely to rust!
|
|
|
