| [ Total Views: 35041 | Total Replies: 57 | Thread Id: 79954 ] |
| Pages: 1 2 |
|
|
 Purple Martin
A.k.a.: Martin
Fahrvergnugen
Posts: 913
Threads: 141
Registered: February 13th, 2003
Member Is Offline
Location: Canberra
Theme: UltimaBB Pro Blue ( Default )
Mood: warm & fuzzy
|
 posted on October 30th, 2009 at 01:23 PM |
|
|
fitting electric fuel pump
I'm considering fitting an electric fuel pump to my '59 beetle with a 1600 engine. I've heard that the best location is under the fuel tank, and I
have a couple of other questions about how to do this properly...
What is the right knd of pressure range needed?
Where should the pump get electric power from?
Do I need some kind of safety cut-off, if so how should that be set up?
Thanks in advance
1959 red & white Beetle
1975 Kombi camper
|
|
|
Adsman
Officially Full-On Dubber
Posts: 393
Threads: 21
Registered: January 23rd, 2007
Member Is Offline
Location: Townsville
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 30th, 2009 at 01:49 PM |
|
|
You will need to buy a pump to suit a carby motor they run a lower pressure around 4.
Yes fitting them under the fuel tank is a good idea to prevent the pump sucking air.
You won't necessarily need any safety cut off for fuel pressure but depending on your carby an aftermarket fuel pressure regulator might be helpful.
(try without first most times not needed, as pumps have an internal pressure regulator)
To power your pump its a good idea to run a new feed from the battery via a relay to the pump switch the relay off your ignition (saves filling the
motor with fuel if you forget to turn off the pump after stopping the engine..lol)
Its also a good idea to rubber mount your pump as it saves some of the vibration noise in the cab (just remember to add an earth strap to the pump
housing if rubber mounting)
What my garage isn't messy........Well chaos is a form of order isn't it?
|
|
|
HotRodMatt
Wolfsburg Elder
If it's old or rare - cut it!
Posts: 3616
Threads: 361
Registered: September 3rd, 2002
Member Is Offline
Location: West of Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 30th, 2009 at 03:19 PM |
|
|
| Quote: | Originally
posted by Adsman
You won't necessarily need any safety cut off for fuel pressure
|
But you are required to have a tachometric relay or similar to switch off the pump if the engine stops.
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on October 30th, 2009 at 08:19 PM |
|
|
i agree with HotRodMatt you definitely need a cut out in case of accident,there would be nothing worse than being in a vehicle after a crash with the
engine stopped and the fuel pump spraying fuel over a hot motor through a ruptured fuel line whilst you were trapped or incapaitated.I use a relay
triggered by the oil pressure switch which cuts the fuel when there is no fuel pressure. As there is usually fuel in the carby there is no problem
starting. Cheers Les
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on October 31st, 2009 at 08:51 PM |
|
|
what makes you want to go electric?
stock works well even feed a pair of IDAs
i ran one while ago but only cos i had no choice
first round it was wired by the charge light so it only ran when the alternator spun and second round i got a EFI fuel pump relay which works of tacho
signal
they're usually noisy and pressure can be a problem with some carbs
kadrons are painfull with electric pumps
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 31st, 2009 at 09:55 PM |
|
|
| Quote: | Originally
posted by Purple Martin
I'm considering fitting an electric fuel pump to my '59 beetle with a 1600 engine. I've heard that the best location is under the fuel tank, and I
have a couple of other questions about how to do this properly...
What is the right knd of pressure range needed?
Where should the pump get electric power from?
Do I need some kind of safety cut-off, if so how should that be set up?
Thanks in advance
|
Hi
Yes,
I have mine mounted under the tank...
I have it wired to the ignition thru a switch which is under the dash... so i can switch it off any time...
You only need about 2 PSI of fuel pressure so You don't need any large capacity pumps..
Mine is very quiet.. I only hear it when i turn the key on..
I ended up getting a fuel pressure regulator and gauge...
LEE
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 31st, 2009 at 11:42 PM |
|
|
http://inlinethumb04.webshots.com/32771/1146550404050767931S600x600Q85.jpg
Hi,
from My website..
a photo of under My fuel tank
I hope it turns Out OK..
a bit hard to see..
the round black plastic fuel pumps is under the steering column
My electric air horns are on the RHS,,
You will also notice the collapsible steering column...
every beetle should be fitted with one of these....
I think they started in 1968>
I also have fitted a collapsible steering wheel...
from a late type 3 VW...
cheers
LEE
http://community.webshots.com/user/vw68autobug
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
baybug
Learner Dubber
Posts: 16
Threads: 5
Registered: April 4th, 2009
Member Is Offline
Location: Hervey Bay
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 3rd, 2009 at 06:24 PM |
|
|
i have just purchased an electric fuel pump ( facet type with a pressure of 1.5 - 4 psi) for my 1600 L bug , stock motor with new solex 34pic carby.
i was going to mount the pump in the engine bay on the passenger side panel. i have an oil pressure switch to run it through
1. will that get to hot for it there ?
2. from previous threads i am gatheriong i don't need a regulator, is that right?
Cheers
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on November 3rd, 2009 at 06:46 PM |
|
|
Hi
If you look at the instruction sheet that came with the pump, there are special things you need to do, it needs to be lower than the tank and close to
the tank, inside the engine bay is the worst place to fit it.
Steve
|
|
|
baybug
Learner Dubber
Posts: 16
Threads: 5
Registered: April 4th, 2009
Member Is Offline
Location: Hervey Bay
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 3rd, 2009 at 07:20 PM |
|
|
thanks - i will go looking for a spot under the tank
|
|
|
HotRodMatt
Wolfsburg Elder
If it's old or rare - cut it!
Posts: 3616
Threads: 361
Registered: September 3rd, 2002
Member Is Offline
Location: West of Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 3rd, 2009 at 07:52 PM |
|
|
| Quote: | Originally
posted by 68AutoBug
I have it wired to the ignition thru a switch which is under the dash... so i can switch it off any time...
|
Except if you crash and burn to death...
Having an automated power shut off is one requirement that makes sense!
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on November 3rd, 2009 at 08:02 PM |
|
|
| Quote: | Originally
posted by baybug
i have just purchased an electric fuel pump ( facet type with a pressure of 1.5 - 4 psi) for my 1600 L bug , stock motor with new solex 34pic carby.
i was going to mount the pump in the engine bay on the passenger side panel. i have an oil pressure switch to run it through
1. will that get to hot for it there ?
2. from previous threads i am gathering i don't need a regulator, is that right?
Cheers
|
Hi
I got away without a fuel regulator for about 6 months...
then My engine started to flood....
I left My key on one day and fuel was coming out My muffler...
You don't need more than 2 PSI...
and under the fuel tank is best...
some pumps need to be in a certain position too...
make sure you have a fuse in line plus a fuel filter....
cheers
LEE
I have got a pic somewhere??
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on November 3rd, 2009 at 08:36 PM |
|
|
| Quote: | Originally
posted by baybug
i was going to mount the pump in the engine bay on the passenger side panel. i have an oil pressure switch to run it through
|
definately under the tank
my rotary converted bug had one there and the pumps can run dry on a low tank if u face down hill
electric pumps need a good gravity feed
only place to get that is under the tank
|
|
|
baybug
Learner Dubber
Posts: 16
Threads: 5
Registered: April 4th, 2009
Member Is Offline
Location: Hervey Bay
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 3rd, 2009 at 08:44 PM |
|
|
thanks again
yes i have got a oil pressure switch to cut off power if oil pressure drops.
i kinda figured that the engine bay may gat a bit hot as well for the pump
i will take advice and get a regulator about 2psi, if i can find one
cheers
|
|
|
baybug
Learner Dubber
Posts: 16
Threads: 5
Registered: April 4th, 2009
Member Is Offline
Location: Hervey Bay
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 4th, 2009 at 09:00 AM |
|
|
just a few more silly questions
does the fuel pump need to be bfore the filter and does the regulator need to be close to the pump ?
cheers
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on November 4th, 2009 at 02:27 PM |
|
|
doesnt matter where the reg is just as long as its before the carbs 
definately put the filter before the pump
electric pump have a habit of stopping at inconvenient times when rust flakes from the tank try to go through them
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on November 4th, 2009 at 04:38 PM |
|
|
| Quote: | Originally
posted by baybug
thanks again
yes i have got a oil pressure switch to cut off power if oil pressure drops.
i kinda figured that the engine bay may gat a bit hot as well for the pump
i will take advice and get a regulator about 2psi, if i can find one
cheers
|
Hi
Regulators - Holley is the most common type...
but there are a few different ones about...
and they ARE adjustable....
just screw or dial in the lowest setting..
I have My regulator in the engine bay...
but the pump and filter is under the fuel tank..
I ended up buying a fuel pressure gauge to see what the pressure was.. .lol
I really only wanted to check the pressure... Oh welll..
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on November 4th, 2009 at 04:40 PM |
|
|
| Quote: | Originally
posted by baybug
thanks again
yes i have got a oil pressure switch to cut off power if oil pressure drops.
i kinda figured that the engine bay may gat a bit hot as well for the pump
i will take advice and get a regulator about 2psi, if i can find one
cheers
|
I just found a circuit diagram for a fuel pump in one of My folders... lol...
which includes a relay and cut off.. lol
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
baybug
Learner Dubber
Posts: 16
Threads: 5
Registered: April 4th, 2009
Member Is Offline
Location: Hervey Bay
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 4th, 2009 at 05:12 PM |
|
|
thanks
i would love a copy of the circut diagram just to make sure i am doing it right.
i have a pressure regulator from local speed shoop dial up the pressure frpm 0.5 to 5 psi and i think it will end up in the engine bay.
it is tight under the tank to find a spot for the pump. will they work mounted on their side to the viertical wall or do they have to be flat
cheers
|
|
|
11CAB
Compulsive Aussie Vee Dubber
If ya got it....Baja it
Posts: 4674
Threads: 321
Registered: August 30th, 2002
Member Is Offline
Location: Brisbane Northside
Theme: UltimaBB Pro Blue
Mood: Beach'n
|
| posted on November 4th, 2009 at 06:53 PM |
|
|
Here's a link that uses a normal switching relay off the charge light circuit.
http://www.the12volt.com/installbay/forum_posts.asp~TID~107789~PN~5
65 Meyers Manx
68 Country Buggy (KO 367)
68 Country Buggy (KO 669)
68 Country Buggy (KO 789)
68 Country Buggy (KO 815)
68 Baja Bug
76 Baja Kombi Twincab
|
|
|
baybug
Learner Dubber
Posts: 16
Threads: 5
Registered: April 4th, 2009
Member Is Offline
Location: Hervey Bay
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 5th, 2009 at 07:18 PM |
|
|
got the fuel pump all done and fitted under the tank near the filter, i ended up getting an aftermarket regulator that was adjustable 0 - 5 psi
!!!!!!! turns out it was adjustable 0 -0, it completely blocked all fuel flow. so i threw it back to the shop. trying it without one for a while
and see.
huge improvement in the bug, though that may also be due to the new carby and manifolds as well
thanks all for your advice, it is reallly great being part of the vw family
cheers
|
|
|
Purple Martin
A.k.a.: Martin
Fahrvergnugen
Posts: 913
Threads: 141
Registered: February 13th, 2003
Member Is Offline
Location: Canberra
Theme: UltimaBB Pro Blue ( Default )
Mood: warm & fuzzy
|
| posted on November 16th, 2009 at 01:56 PM |
|
|
I've had an idea...
As has been said, the relay can run from the charge light circuit so the pump will cut out if the engine stops.
I read somewhere that someone also put a relay by-pass push-button switch on the dash so they can fill the carb before starting the car. My idea is:
instead of using a relay by-pass switch, use a second relay that runs from the starter motor circuit to fill the carb while cranking.
Am I mad?
1959 red & white Beetle
1975 Kombi camper
|
|
|
11CAB
Compulsive Aussie Vee Dubber
If ya got it....Baja it
Posts: 4674
Threads: 321
Registered: August 30th, 2002
Member Is Offline
Location: Brisbane Northside
Theme: UltimaBB Pro Blue
Mood: Beach'n
|
| posted on November 16th, 2009 at 05:28 PM |
|
|
The link I posted above does that as well, but all with the one relay. You can buy them at Repco for about $13
65 Meyers Manx
68 Country Buggy (KO 367)
68 Country Buggy (KO 669)
68 Country Buggy (KO 789)
68 Country Buggy (KO 815)
68 Baja Bug
76 Baja Kombi Twincab
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on November 16th, 2009 at 06:36 PM |
|
|
| Quote: | Originally
posted by Purple Martin
I've had an idea...
As has been said, the relay can run from the charge light circuit so the pump will cut out if the engine stops.
I read somewhere that someone also put a relay by-pass push-button switch on the dash so they can fill the carb before starting the car. My idea is:
instead of using a relay by-pass switch, use a second relay that runs from the starter motor circuit to fill the carb while cranking.
Am I mad?
|
its been done
works well
heres a diagram
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on November 16th, 2009 at 08:22 PM |
|
|
Good info above. Thanks Joel.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
snowman9
Casual Dubber
Posts: 38
Threads: 10
Registered: December 7th, 2009
Member Is Offline
Location: Central Coast NSW
Theme: UltimaBB Streamlined2
Mood: Happy
|
| posted on July 18th, 2010 at 09:46 AM |
|
|
My thanks Joel as well. 
|
|
|
General_Failure
A.k.a.: Tristan
Custom Title Time!
Use your head, don't abuse it!
Posts: 1036
Threads: 107
Registered: June 15th, 2004
Member Is Offline
Location: Peaceful Finley, NSW
Theme: UltimaBB Streamlined2
Mood: Not too bad. Thanks for asking!
|
| posted on July 26th, 2010 at 12:09 PM |
|
|
I'm using a tacho relay from a VK Dunnydoor. Works a treat even though my relay's primer function seems to be buggered.
Recently i ended up with a tacho relay used in LPG systems. Looks like it would do the job pretty much as well, so even though it isn't pin
compatible I have a spare if I need it.
If at first you don't succeed. Build, build again.
Vehicle: 1975 Special order delivery walkthrough panel based LCA pop-top camper. Motor: Nippon 1.8L Single port Wasserboxer, Transmission: 3 rib 002.
|
|
|
VolksVair
Officially Full-On Dubber
Posts: 252
Threads: 32
Registered: April 6th, 2010
Member Is Offline
Location: Geelong VIC
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2011 at 06:36 PM |
|
|
Any electric fuel pump installation i do, I run the power through an oil pressure switch, "No oil pressure, No fuel pressure" A 12V shut off
valve is a good bonus too
Adventure Before Dimentia
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on June 1st, 2011 at 06:58 PM |
|
|
That's all well and good on a fresh engine but one that's got a few miles under it's belt can take a few seconds to get oil pressure and when hot
the oil light can flicker at idle which can upset the relay or worse yet cut the fuel pump out.
not fun when you're sitting at traffic lights.
It's so easy to get a tachometric fuel pump relay, nearly all fuel injected cars use them.
I had one from a Commodore and it was great, it primed the pump for 2 secs when you turned the ignition on then waited for a tacho signal before it
ran again and stopped soon as the tach signal stopped.
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on June 1st, 2011 at 07:29 PM |
|
|
i rekon having that tachometer based switch or charge light off the alternator is the way to go,
but have an override momentary push button that you hold while cranking to 'prime' then of course the alternator or tacho goes and u let go of the
override then technically it should run itself :P
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
| Pages: 1 2 |
