| [ Total Views: 2674 | Total Replies: 12 | Thread Id: 87229 ] |
|
|
 rustguard
Casual Dubber
Posts: 45
Threads: 10
Registered: March 7th, 2009
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: always
|
| posted on November 19th, 2010 at 11:32 PM |
|
|
wasserboxer reseal
The seals are seeping on my wasserboxer, although not low k's (over 200 000) it runs great and doesn't burn oil.
it needs a seal kit
The only thing I am worried about is I'm not sure how the former owner treated it. I am deathly afraid of opening a can of worms
My first question is this-
What worms could I expect to find?
Second question-
The Brasilian made barrel, piston and ring kits are quite cheap, should I throw one in.
I wont be touching the bottom end or rods, good german stuff should have no problems with more k's
My biggest concern is finding loads of corrosion in the alloy mating faces and rusted in studs.
If there are any who have done a few of these motors what do you usually find?
What condition are the studs in after 20+ years in the drink?
Aftermarket stainless studs?
There is alot I like about this engine design. If only they hadn't put the engine studs in the water jacket. Why oh why?
any reply's appreciated
dak dak dak dak dak dak
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 20th, 2010 at 06:37 AM |
|
|
what seals you talking about??
Water or oil??
"My biggest concern is finding loads of corrosion in the alloy mating faces and rusted in studs"
dead right!
Has the propper G12++ coolant been used?? and regularly changed?
Where abouts are you?
There are a few of us here with these
A few aven know how to fix them
Grumble and Menangler are good sources of info
Have you checked out
http://www.brick-yard.co.uk/forum/
Can be a bit "funny" but a lot of info there
Futue te ipsum!!!
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on November 20th, 2010 at 07:43 AM |
|
|
Beware, can be very likely that you will have more to do than seals. You can have the possibility of a complete teardown if there are problems with
head studs.
Normally the higher mileage cars are good, lower mileage or non genuine coolant vehicles are the worst. At 200k yours unfortunately falls into the
lower mileage group....just, so you never know, was it genuinely (VW) serviced for long, the books should tell you.
I recently had a head off my own T3, at 360k km, an genuine servicing untill 160k, and a comercial van in Sydney (thrashed most likely :tu , the insides were like NEW, studs, bores amd area's that corode....like
new.
But if a head stud is coroded, jus one even, and on removal, it breaks down loww in the block........a very difficult to repair situation arises.
Steve at Kombi Rescue has done plenty. ph 0400 356 057.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
rustguard
Casual Dubber
Posts: 45
Threads: 10
Registered: March 7th, 2009
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: always
|
| posted on January 8th, 2011 at 08:59 PM |
|
|
| Quote: | Originally
posted by Bizarre
what seals you talking about??
|
the head water seals.
I have been told that the o-rings at the bottom of the barrel can leak, if while apart the barrel moves at all. so they should always be removed and
new o-rings installed.
This is why I was thinking to put a barrel kit in while it is apart.
Anyone ever just replaced the head seals and left everything else alone?
dak dak dak dak dak dak
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on January 9th, 2011 at 07:18 AM |
|
|
| Quote: | Originally
posted by rustguard
Anyone ever just replaced the head seals and left everything else alone?
|
Yes, I've done a few.....my post above is still relevant. There is the possibility of a total engine rebuild if any studs are corroded and don't
come out of the block.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
rustguard
Casual Dubber
Posts: 45
Threads: 10
Registered: March 7th, 2009
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: always
|
| posted on January 29th, 2011 at 03:29 PM |
|
|
Thanks for the headsup matbury, any stubborn studs, I'll make sure to gently heat them out before I break one.
So do the wasserboxer's use the same pushrod tube seals?
I'll guess possibly yes? fingers crossed.
dak dak dak dak dak dak
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on January 29th, 2011 at 10:55 PM |
|
|
Same at one end, but bigger at the other. Most seals are available separately.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
johny rotten
Officially Full-On Dubber
Posts: 366
Threads: 5
Registered: April 6th, 2004
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 30th, 2011 at 09:27 AM |
|
|
don't use heat on the the engine case 
if the studs look OK you might get away without changing them
they don't wind out easily in general
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on January 30th, 2011 at 09:34 AM |
|
|
Oh yeah....lotsa luck if removal is necessary.....NO HEAT !!!
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
rustguard
Casual Dubber
Posts: 45
Threads: 10
Registered: March 7th, 2009
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: always
|
| posted on March 5th, 2011 at 08:09 PM |
|
|
Well I saw some stainless engine studs on an american site, I was going to change them over and put in new liners. might just leave the ones in there
alone.
Will heating the studs affect the block? Gentle heat on the stud should weaken the chemical bond that has formed and the little heat that soaks into
the block it shouldn't be much different to operating heat. I would have thought that would be preferable to drilling a seized steel stud out of a
aluminium hole?
Of coarse, the image of backyard joe going to town with a torch would be enough to scare anyone. I've seen even qualified trades people heating the
tripe of of things. ouch
Of which i am; a fitter/1st class machinist, done quite a few engine rebuilds and plenty of machining, gearboxes of many descriptions. But NO
wasserboxes.
I have removed a ton of sheared and rusted bolts and studs from all sorts of things. I hate drilling high tensile bolts out of aluminium in hard to
get to places.
anyhow nothing that a shifter and a bigger hammer wont fix(just kidding(I hope))
I'm letting it sit for a little longer while I mop up a few of my smaller projects, as soon as i drop the engine I want to give it 100% focus.
dak dak dak dak dak dak
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on March 5th, 2011 at 08:34 PM |
|
|
Hi
I've been told by experienced people that if your going to remove the head studs do it as soon as you can after stripping the motor as they get more
stuck as the case dries out.
I tried to remove the studs from my WBX that had always used genuine coolant and fit heavy BAS studs, not wanting to force the issue I gave up, the
original ones were like new anyway
Steve
|
|
|
rustguard
Casual Dubber
Posts: 45
Threads: 10
Registered: March 7th, 2009
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: always
|
| posted on March 22nd, 2011 at 12:05 AM |
|
|
Thanks for the info steve, unfortunately the seals were seeping so the collant level will be well down already. Judging by the drip tray underneath a
bit too. If nothing else comes up, I will start next week! | Quote: | Originally posted by 1303Steve
and fit heavy BAS studs
|
What did you do with the studs?
dak dak dak dak dak dak
|
|
|
rustguard
Casual Dubber
Posts: 45
Threads: 10
Registered: March 7th, 2009
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
Mood: always
|
| posted on March 27th, 2011 at 06:31 PM |
|
|
http://www.evwparts.com/vwparts/VanPistonCylRing/025198075.html
http://www.evwparts.com/vwparts/VanGasketSets/025198009B.html
Anyone know what the local shops are charging for this sort of kit?
dak dak dak dak dak dak
|
|
|
