| [ Total Views: 513 | Total Replies: 3 | Thread Id: 88541 ] |
|
|
 karmann54
Officially Full-On Dubber
Posts: 337
Threads: 87
Registered: November 4th, 2002
Member Is Offline
Location: Kangaroo Point, Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 5th, 2011 at 04:54 AM |
|
|
12V genny fan rub
I'm converting my '67 beetle to 12V, and when I've mounted the fan on the genny shaft there is a rub between the back of the fan and the backing
plate.
The fan is mounted onto the hub with no washers/spacers at back. At the front there is a washer and lock nut. The 'washer' is a special with the
cut-out to suit the drive shaft.
My question is, should there be spacers between the hub and the shaft to shift the fan axially out along the shaft and thus clear the backing plate.
My feeling is it's more likely my backing plate is a little warped but just wanted to check before I start any panelbeating on it - I've only got
one!
Thanks, Angus
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on February 5th, 2011 at 07:47 AM |
|
|
Are all the shims missing?
There should be half a dozen or so, same as the pulley has, the unused ones go on the front side under the nut.
Needs to be spaced out so it sits in the center of both the shroud and the backing plate.
|
|
|
karmann54
Officially Full-On Dubber
Posts: 337
Threads: 87
Registered: November 4th, 2002
Member Is Offline
Location: Kangaroo Point, Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 5th, 2011 at 07:53 AM |
|
|
Joel
Thanks for that. There were no shims at all. When I pulled apart another genny/fan I had this morning it had a single shim, but it is still not
enough.
Now knowing there should be half a dozen or so makes it simple.
I'll dig around to see if I have any lying around. I didn't even know I had this other genny and fan, it's amazing how VW crap seems to
accumulate....
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on February 5th, 2011 at 09:46 AM |
|
|
| Quote: | Originally
posted by karmann54
I'm converting my '67 beetle to 12V, and when I've mounted the fan on the genny shaft there is a rub between the back of the fan and the backing
plate.
The fan is mounted onto the hub with no washers/spacers at back. At the front there is a washer and lock nut. The 'washer' is a special with the
cut-out to suit the drive shaft.
My question is, should there be spacers between the hub and the shaft to shift the fan axially out along the shaft and thus clear the backing plate.
My feeling is it's more likely my backing plate is a little warped but just wanted to check before I start any panelbeating on it - I've only got
one!
Thanks, Angus
|
should be heaps of shims....
the spare ones are kept under the nut and washer
every generator had them..
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
