| [ Total Views: 842 | Total Replies: 19 | Thread Id: 91771 ] |
|
|
 vwbugsrule
Slammed & Awesome Dubber
Posts: 84
Threads: 26
Registered: February 10th, 2011
Member Is Offline
Location: Kellyville NSW
Theme: UltimaBB Pro Blue ( Default )
|
 posted on July 25th, 2011 at 02:38 PM |
|
|
unlocking the gland nut ?
I got me 36mm socket for the flywheel gland nut, my only problem is what tool/s do i need to to unlock this nut?
|
|
|
 barls
A.k.a.: Mr indestructible
Super Administrator
Causer of Chaos and Mayhem
Posts: 9467
Threads: 295
Registered: June 22nd, 2004
Member Is Offline
Location: cruising in denistone east
Theme: UltimaBB Streamlined2
Mood: indestructible? and listening to the voices
|
| posted on July 25th, 2011 at 02:51 PM |
|
|
http://www2.cip1.com/ProductDetails.asp?ProductCode=ACC%2DC10%2D7025
one of these
|
|
|
vwbugsrule
Slammed & Awesome Dubber
Posts: 84
Threads: 26
Registered: February 10th, 2011
Member Is Offline
Location: Kellyville NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 25th, 2011 at 04:51 PM |
|
|
thats not my problem, i have a "piston stop" to stop the flywheel from rotating. But my actual problem is unlocking the grand nut. (i already
snapped my ratchet in half)
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 25th, 2011 at 04:58 PM |
|
|
Were you using 1/2" drive?
Don't waste your time with 1/2" drive sockets on axle and flywheel nuts, even good quality breaker bars break if they;ve been torqued up right.
3/4" and a pipe over the handle 
|
|
|
vwbugsrule
Slammed & Awesome Dubber
Posts: 84
Threads: 26
Registered: February 10th, 2011
Member Is Offline
Location: Kellyville NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 25th, 2011 at 05:00 PM |
|
|
oh bloody hell, i just ordered/ got a 1/2 inch drive socket custom made.... fml LOL is there any other way ??
|
|
|
Birdman
Wolfsburg Wizard
Posts: 428
Threads: 49
Registered: May 19th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 25th, 2011 at 05:35 PM |
|
|
Torque Meister, you can borrow mine.
|
|
|
eraser
Fahrvergnugen
Posts: 970
Threads: 128
Registered: March 11th, 2005
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Powder
|
| posted on July 25th, 2011 at 08:27 PM |
|
|
i used an air impact drill, i had to turn the compressor up into the red but after about 3 minutes of it tapping away it finally came undone (this was
with a flexplate that is about 240-250ish ft pounds).. god knows how im going to do it back up... i understand the idea of a ratchet with a pole on it
but i dont get how to keep the motor from breaking a head.
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on July 25th, 2011 at 08:49 PM |
|
|
I got my mate over who has a air impact gun on his work truck. Took about 5 seconds to get off. Make sure you have a torque wrench to tighten it to
the correct torque. I had to remove the flywheel again about 2 weeks later but used a 1/2 inch breaker bar and steel pole over the bar to get it off.
|
|
|
Gracey
Wolfsburg Wizard
Posts: 511
Threads: 17
Registered: February 6th, 2003
Member Is Offline
Location: Beaudesert, Qld
Theme: UltimaBB Pro Blue
Mood: Itchy
|
| posted on July 25th, 2011 at 08:56 PM |
|
|
I use a piece of steel tube about 1200mm long bolted to the flywheel via the clutch mounting holes.
Then as mentioned above a 36mm 3/4" drive socket and breaker bar and then I put a length of pipe over this for leverage.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 25th, 2011 at 09:25 PM |
|
|
Rattle gun? 
Axle nut yea, but the flywheel, sorry but that is asking trouble.
|
|
|
ratty 63
A.k.a.: Rossco
Custom Title Time!
Posts: 1083
Threads: 74
Registered: October 1st, 2003
Member Is Offline
Location: Gold Coast, Qld
Theme: UltimaBB Pro Blue ( Default )
Mood: Just cured my shed envy! 
|
| posted on July 25th, 2011 at 09:44 PM |
|
|
I've used a rattle gun many times to get the flywheel nut on and off - never had a problem
I have also used a decent breaker bar with a pipe over the handle and it worked... but I have seen breaker bars snap and sockets explode from the
amount of force required when using this method, so be sure to use good quality tools and be careful.
Joel, why would using a rattle gun to get the flywheel nut off be 'asking for trouble'?
R 
|
|
|
Old Rusty_VW
Casual Dubber
Posts: 29
Threads: 1
Registered: March 14th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 25th, 2011 at 09:57 PM |
|
|
| Quote: | Originally
posted by vwbugsrule
I got me 36mm socket for the flywheel gland nut, my only problem is what tool/s do i need to to unlock this nut?
|
http://forums.aussieveedubbers.com/viewtopic.php?tid=78351&page=1#pid728699
Also found this with a search. Related to rear axle nut but same principle as flywheel nut.
http://forums.aussieveedubbers.com/viewtopic.php?tid=85569&page=1
Rus
|
|
|
pod
A.k.a.: paul mrvw061
Compulsive Aussie Vee Dubber
i`ve got to finish this thing one day
Posts: 4980
Threads: 145
Registered: December 28th, 2003
Member Is Offline
Location: campbelltown,nsw
Theme: UltimaBB Pro Yellow
Mood: could be better
|
| posted on July 26th, 2011 at 12:56 AM |
|
|
with my semi-auto i used an old bottom belt pulley with a lump of pipe welded to it ,then on the gland nut i have 3/4 drive 36mm socket with a breaker
and a length of pipe
|
|
|
vwbugsrule
Slammed & Awesome Dubber
Posts: 84
Threads: 26
Registered: February 10th, 2011
Member Is Offline
Location: Kellyville NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 26th, 2011 at 07:38 AM |
|
|
i might look into getting that breaker bar, i have some solid tubing so hopefully that will get me through.
Thanks for the replies
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on July 26th, 2011 at 09:16 AM |
|
|
I'm pretty sure i got my breaker bar from Bunnings or Blackwoods.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 26th, 2011 at 10:09 AM |
|
|
| Quote: | Originally
posted by ratty 63
Joel, why would using a rattle gun to get the flywheel nut off be 'asking for trouble'?
R
|
You could probably do it 9 times out of 10 and not damage anything but the shock to the crank from a rattle gun that actually has the balls to undo
one that is torqued to the right value has a chance of damaging several things - dowel pins, bearings, crank thread, even the seats in the case -
butter would be stronger than mag cases.
To me it's not worht the risk of requiring a full engine tear down to repair something for the sake of not bolting a bar to the flywheel and using a
controlled force with the breaker bar.
Not many people actually use a torque wrench and take them up to the required torque.
Must admit I've done it enough times now I go by feel but i've pulled down a few engines that the nut wasnt torqued up enough.
A loose flywheel does all sorts of damage.
|
|
|
Sides
A.k.a.: Dave Sidery
Veteran Volks Folk
Posts: 2220
Threads: 59
Registered: May 20th, 2007
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
Mood: Need... more... shed... time...
|
| posted on July 26th, 2011 at 12:43 PM |
|
|
Yeah, I'm with Joel... rattle gun is a bad idea.
Length of angle bolted to the fly wheel as Gracey has said to hold the engine still, then a good quality 3/4" 36mm flats drive socket with a breaker
bar and extension.
Or better yet a good torque wrench - got myself a giant one couple of years back that goes to 700 Nm / 520 lb-ft... some of the best tool $$$ I've
ever spent I reckon
VWDCQ vice pres & web dude - vwdcqinc.org.au
Join a car club - get car peeps
My toys
'70 Hillclimb Bug 'Jezebel' w/- Haltech EFI - http://bit.ly/VwTNtQ
'60 KG Coupe - resto kinda started
01 New Beetle - gf's car, but I turn the spanners |
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 26th, 2011 at 12:47 PM |
|
|
My trusty bit of angle and 3/4 breaker bar have never failed me on a flywheel or rusted up axle nut yet
Even on some of the rusty old shitters I've pulled out jungle backyards
|
|
|
bnicho
A.k.a.: Brett Nicholson
Wolfsburg Wizard
Posts: 436
Threads: 55
Registered: February 24th, 2009
Member Is Offline
Location: Melbourne, Australia
Theme: UltimaBB Pro Blue ( Default )
Mood: Usually Cranky!
|
| posted on July 26th, 2011 at 03:13 PM |
|
|
I did the clutch and main seal a couple of weeks ago. To hold the engine from turning over I bought a flywheel lock from Mick's Motors.
Coincidentally it fits Mini flywheels too so it will come in useful for my other cars.
I used a 3/4" drive breaker bar with a Moke bumper over the end (approx 1.3 metres long). That got it undone.
To do it up I borrowed a 3/4" drive torque wrench from a mate.
Brett Nicholson
Melbourne, Victoria
1974 VW Superbug L - Olive 
1971 Morris Mini Moke - Mopoke
1966 Austin Mini - Audrey
1965 Morris Mini Traveller - Trixie
2007 Land Rover Freelander 2
2009 Nissan Pathfinder |
|
|
beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on July 26th, 2011 at 10:17 PM |
|
|
| Quote: | Originally
posted by Joel
My trusty bit of angle and 3/4 breaker bar have never failed me on a flywheel or rusted up axle nut yet
|
That is pretty well identical to the setup I use, except for the length of gal. pipe I put over the handle of the breaker bar.
Haven't had a problem yet (touch wood).
From your ole' mate Jeff
|
|
|
