| [ Total Views: 728 | Total Replies: 5 | Thread Id: 93085 ] |
|
|
 mjwcookie
Seriously Crusin Dubber
Posts: 105
Threads: 57
Registered: March 21st, 2011
Member Is Offline
Location: Point Lonsdale, Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 8th, 2011 at 02:40 PM |
|
|
advice needed in doing the heads in 89 water boxer
hi all. all advice gratefully received.
I am doing the heads on my 89 caravelle 2.1 injected. and have a few questions.
1. the fuel lines to the injector rails are old, can i just replace them or do i have to buy special ones? do they have to be exactly same length as
the old ones? can i flush out the rails as i have had a problem with water in fuel somehow.
2. is there a trick to separating the sleeves from the heads before they slip off the pistons? Do the sleeves have sealing rings around their bases on
the block?
3. i think the water pump is original and done 210k. should i replace it?
4. as the heads loosened, water leaked into the block, as I could not open the drain plugs under the pushroods. Seazed up and i did not want to break
or crack anything. how can i be sure to have it all (water) our when i go to refill with oil?
Thanks. That is it so far.
Mark Wilson
Mark Wilson
78 bay window, 82 bay Westy. T3 Caravelle GL 89 on the road.
Now in Victoria.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 8th, 2011 at 07:29 PM |
|
|
Talk to VVDS at Campsie info@vintageveedub.com.au
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on October 8th, 2011 at 08:49 PM |
|
|
| Quote: | Originally
posted by mjwcookie
hi all. all advice gratefully received.
I am doing the heads on my 89 caravelle 2.1 injected. and have a few questions.
1. the fuel lines to the injector rails are old, can i just replace them or do i have to buy special ones? do they have to be exactly same length as
the old ones? can i flush out the rails as i have had a problem with water in fuel somehow.
2. is there a trick to separating the sleeves from the heads before they slip off the pistons? Do the sleeves have sealing rings around their bases on
the block?
3. i think the water pump is original and done 210k. should i replace it?
4. as the heads loosened, water leaked into the block, as I could not open the drain plugs under the pushroods. Seazed up and i did not want to break
or crack anything. how can i be sure to have it all (water) our when i go to refill with oil?
Thanks. That is it so far.
Mark Wilson
|
In answer to the question No1 I have a set of injection hoses and fittings for a 2.1 and 1 new injector. Contact by pm if interested
no2 yes the main trick is luck,as you release the heads try to pry the cylinder lose from the head ( not usually successful)
No3 Yes replace the pump to save you doing it shortly after putting the engine back together
No4 Drain the oil and leave it draining whilst rebuilding the engine.
Cheers and good luck Les
|
|
|
mjwcookie
Seriously Crusin Dubber
Posts: 105
Threads: 57
Registered: March 21st, 2011
Member Is Offline
Location: Point Lonsdale, Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 8th, 2011 at 09:38 PM |
|
|
how do i replace the sleeves into the block over the rings. seems like not much room. I expect to have to rotate the crank to get the piston all the
way out, then do one, then rotate again. etc. Do the sleeves have sealing rings at the block end?
Mark Wilson
78 bay window, 82 bay Westy. T3 Caravelle GL 89 on the road.
Now in Victoria.
|
|
|
Ben386
Officially Full-On Dubber
Posts: 244
Threads: 26
Registered: April 2nd, 2010
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Never had a bad day
|
| posted on October 9th, 2011 at 09:36 PM |
|
|
http://www.rjes.com/
Dont look back
|
|
|
mjwcookie
Seriously Crusin Dubber
Posts: 105
Threads: 57
Registered: March 21st, 2011
Member Is Offline
Location: Point Lonsdale, Vic
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 10th, 2011 at 01:29 PM |
|
|
If I had the money, I would even bother trying to fix it, just slot in a subi. Unfortunately that is not an option. so far.
thanks.
Mark
Mark Wilson
78 bay window, 82 bay Westy. T3 Caravelle GL 89 on the road.
Now in Victoria.
|
|
|
