| [ Total Views: 1796 | Total Replies: 11 | Thread Id: 95886 ] |
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 18th, 2012 at 09:41 AM |
|
|
Waterproofing Inner door
Anyone got a picture of the inner door with the panel off??
I replaced my door panels the other day because they were cloth and getting dirty.
Turned out to be water coming through. I refixed the plastic that had been torn over the years, but my new panels are wet again.
Yes its been pissing down unnaturally here in Sydney, but my car lives outside 24/7 so I need it fixed
Also what plastic are you using.
I got a large black garbage bag and opened it flat but it seems the be coming through this?? porous??
Would like to see where it is stuck down in the middle to allow the door latch to pass through.
These are 1975 L bug doors if that matters
Barry
Futue te ipsum!!!
|
|
|
 beetleboyjeff
A.k.a.: Jeff Walsh
Custom Title Time!
Posts: 1773
Threads: 40
Registered: February 13th, 2009
Member Is Offline
Location: Port Macquarie
Theme: UltimaBB Pro Blue ( Default )
Mood: Drive bugs hard
|
| posted on March 18th, 2012 at 10:18 AM |
|
|
Barry, the standard door waterproof sheet is normaly just stuck to the inside of the door, directly behind the door cards.
Because I put remote central locking and electric windows in my bug, I moved the waterproof sheet to the back of the inside door skin, but inside the
window glass so I could keep the water off the electrics.
This is the electrics in the door (before the car was re-sprayed).
Central locking -
Electric windows -
So here is the waterproof sheet (I used blue plastic tarpaulin material, because that is what I had) behind the inside door skin.
And here is where I fixed it at the top, to the top of the internal door skin, inside the window glass. I glued it on with contact glue - bugger of a
job though.
That was nearly 5 years ago, and I haven't had any problems so far (touch wood).
From your ole' mate Jeff
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on March 18th, 2012 at 04:02 PM |
|
|
| Quote: | Originally
posted by Bizarre
Anyone got a picture of the inner door with the panel off??
I replaced my door panels the other day because they were cloth and getting dirty.
Turned out to be water coming through. I refixed the plastic that had been torn over the years, but my new panels are wet again.
Yes its been pissing down unnaturally here in Sydney, but my car lives outside 24/7 so I need it fixed
Also what plastic are you using.
I got a large black garbage bag and opened it flat but it seems the be coming through this?? porous??
Would like to see where it is stuck down in the middle to allow the door latch to pass through.
These are 1975 L bug doors if that matters
Barry
|
I think normally they used a clear plastic with adhesive [sticky] on one side and went over the outer door skin then the rubber/plastic plugs fitted
all round... from memory
so no water can touch the door card...
I used thick clear plastic I found somewhere...
Jeffs idea is better...
inside the door... You would need to clean where you are going to glue it.. inside the door under the inner panel so all water drips down into the
bottom of the door..
but the window winder is still a pain..!!
maybe back to the outer part of the door...
remember the original plastic was sticky ALL over..
and went right to the bottom... of the door card so any water would drip from Under the card...
just under the top of the door card and just to the bottom of the door card.. all stuck All over the door...
the water isn't coming in the 1/4 window??? common..
cheers
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Lucky Phil
Wolfsburg Wizard
Posts: 480
Threads: 16
Registered: August 1st, 2010
Member Is Offline
Location: Adelaide SA
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm a legend in my own lunchtime!
|
| posted on April 7th, 2012 at 11:02 PM |
|
|
The plastic bag off a new mattress works well.
Bought a sofa the other day and the plastic it was wrapped in looked pretty good too.
It looked like it came off a continuous roll so try a sofa shop.
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on April 8th, 2012 at 02:10 AM |
|
|
It seems to be the factories desire for residual water that passes into the door to simply pass through into the bottom and via the factory drain
holes.
The only water proofing on my 69' provided courtesy by the factory was the glued on plastic sheet all have refered to thus far, which was just inside
the door card, fastened by glue just inside of the door card clips. Simply keeps the water inside the door, but not pass through the card or into the
cabin. 
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on April 8th, 2012 at 09:32 AM |
|
|
Hi
I have a roll somewhere of good stuff to use, its about as tough as landscaping plastic sheet, you could also cover the back of the door trim with
contact paper for extra insurance.
Steve
|
|
|
lenny1870
Slammed & Awesome Dubber
Posts: 84
Threads: 23
Registered: March 16th, 2012
Member Is Offline
Location: Picton, NSW
Theme: UltimaBB Pro Blue
|
| posted on May 5th, 2013 at 09:03 PM |
|
|
i used this...cheap from bunnings....maybe $10-15
Josh
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
Because there is no other car like a Dub  |
|
|
65busser
Super Moderator
Posts: 1795
Threads: 224
Registered: November 6th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: dakked
|
| posted on May 6th, 2013 at 02:24 PM |
|
|
Here's the original weatherproofing on my 65 German built.
Even on Aussie built it was only ever glued around the perimeter.
If you used repro clip seals they let water in easy. If you didn't use clip seals ... even worse.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on May 6th, 2013 at 04:17 PM |
|
|
It may have only been with 70s Beetles but they also glued rings of foam around the window winder and the handle to stop drafts coming in around
them.
You can see the remains of where it was glued in around Jeffs door handle before his door was resprayed.
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on May 9th, 2013 at 10:05 PM |
|
|
| Quote: | Originally
posted by bajachris88
It seems to be the factories desire for residual water that passes into the door to simply pass through into the bottom and via the factory drain
holes.
The only water proofing on my 69' provided courtesy by the factory was the glued on plastic sheet all have refered to thus far, which was just inside
the door card, fastened by glue just inside of the door card clips. Simply keeps the water inside the door, but not pass through the card or into the
cabin.
|
yes thats how all cars are, but the question is where do you get that glue from?
its more like gum that never drys and has the ability to re glue itself.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on May 9th, 2013 at 10:07 PM |
|
|
| Quote: | Originally
posted by lenny1870
i used this...cheap from bunnings....maybe $10-15
Josh
|
I used that stuff for a spray booth, but its awfully waxy and hard for anything to stick to it. I struggled to get packing tape to stick to it.
guess you could always wax n' grease remover it first?
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on May 9th, 2013 at 10:12 PM |
|
|
| Quote: | Originally
posted by 1303Steve
Hi
I have a roll somewhere of good stuff to use, its about as tough as landscaping plastic sheet, you could also cover the back of the door trim with
contact paper for extra insurance.
Steve
|
few coats of good varnish helps a lot, then always a self adhesive film on it too. just some clear or plain black or white vinyl would be good and
easy to apply.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
