| [ Total Views: 604 | Total Replies: 8 | Thread Id: 98331 ] |
|
|
 eXraycer
Seriously Crusin Dubber
Posts: 166
Threads: 27
Registered: May 16th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 13th, 2012 at 03:22 PM |
|
|
WTB, Type 3 Rear valance panel
Ok I'm having a hard time with the rear valance in my Type 3 rebuild. The vertical indentations are going to take a mountain of time to get right. It
had been crushed upward and we did a fair job to get this far but I'm weighing up the cost and time of fitting another panel section if anyone has
one to sell.
Here's what I mean. The area below the exposed metal where all the vertical indentations are. Hard to see but mine are a bit squashed and out of
shape from the damage. The subsequent repair is a bit like a face that's had too much plastic surgury. (Not quite right)
Any how. Here's what I have.
Here's what I'm after except I need the panel full width to the bumper slots and probably a little taller if possible up to where the rear inner
ducting is connected approximately where the first horizontal crease line is. (About 30-40 mm above the weld in this pic.)
|
|
|
dragsters for life
Fahrvergnugen
Posts: 953
Threads: 51
Registered: May 28th, 2011
Member Is Offline
Location: melburg SE burbs
Theme: UltimaBB Pro Blue ( Default )
Mood: always a happy chappy
|
| posted on August 13th, 2012 at 05:59 PM |
|
|
i painted mine matt black
mine was dented and i couldnt get it to look good
volkaholics.net come check us out
|
|
|
eXraycer
Seriously Crusin Dubber
Posts: 166
Threads: 27
Registered: May 16th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 14th, 2012 at 10:04 AM |
|
|
I might have to try that if I can't get this one sorted. There's a few rust repair sections available in UK but no rear valances that I can find.
|
|
|
ladd
Commited Dubber
Posts: 64
Threads: 24
Registered: October 5th, 2011
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Yellow
|
| posted on August 14th, 2012 at 12:03 PM |
|
|
Looks as though you did a good job getting it back to its original shape. Depending how spot on you want it to be i'd leave it how it is now, looks
fine & your bumper will hide some of it.
Painting it black is a good disguise too.
|
|
|
eXraycer
Seriously Crusin Dubber
Posts: 166
Threads: 27
Registered: May 16th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 14th, 2012 at 01:22 PM |
|
|
Thanks mate. Yeah it was pretty bad when we started.
It depends entirely on how obsessive compulsive I'm gonna be about this build. So far I'm showing high OCD tendencies. It would be nice to find the
piece so I can move on to the next part to obsess about. lol.
|
|
|
lauw58
Learner Dubber
Posts: 13
Threads: 2
Registered: March 6th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 23rd, 2012 at 01:37 PM |
|
|
TYPE 3 REAR APRON
I've got that section in a car I'm parting out. Where are you located? bEST RING ME ON 0412183098. ThANKS ....AJ
|
|
|
eXraycer
Seriously Crusin Dubber
Posts: 166
Threads: 27
Registered: May 16th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 23rd, 2012 at 05:37 PM |
|
|
Cheers,
Thanks mate.
|
|
|
rebel
Seriously Crusin Dubber
Posts: 181
Threads: 48
Registered: June 14th, 2008
Member Is Offline
Location: Kellyville
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 23rd, 2012 at 08:39 PM |
|
|
are late and early cars the same valance
|
|
|
eXraycer
Seriously Crusin Dubber
Posts: 166
Threads: 27
Registered: May 16th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 24th, 2012 at 02:05 PM |
|
|
From the outside they look the same to me.
|
|
|
