| [ Total Views: 727 | Total Replies: 6 | Thread Id: 100145 ] |
|
|
 karmann54
Officially Full-On Dubber
Posts: 337
Threads: 87
Registered: November 4th, 2002
Member Is Offline
Location: Kangaroo Point, Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 14th, 2012 at 08:29 PM |
|
|
1200 D engines
Hello
A query about a 1200 engine. There were some D code engines produced I think for poverty pack type models in europe well after the 1300s and 1500s
were introduced. I believe these were the same as the earlier 1200 40HP engines, maybe with an improvement to oil gallerys but heads/crank etc all
the same.
Can anyone confirm that one way or the other?
Thanks, Angus
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 14th, 2012 at 10:15 PM |
|
|
Yep, later so larger oil galleries and cam bearings by memory.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Burrelli
Officially Full-On Dubber
Posts: 244
Threads: 4
Registered: October 12th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 14th, 2012 at 10:34 PM |
|
|
Yes 1200D came out in the 68-72 1200 standard, maybe later cars as well.
The formular V guys liked them.
I think they had all those improvements and even the heads were improved some how.
Apparently they went a lot better than the early 1200s.
|
|
|
karmann54
Officially Full-On Dubber
Posts: 337
Threads: 87
Registered: November 4th, 2002
Member Is Offline
Location: Kangaroo Point, Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 14th, 2012 at 10:51 PM |
|
|
Thanks for the replies, confirms what I suspected. I've come across a double carb kit that was made for a 1200 D engine and I just wanted to check
it was OK for my '63 1200.
As it is just oil galleries/cam bearings etc it should be fine.
Thanks again
Angus
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 15th, 2012 at 01:22 PM |
|
|
you can fit twin carbs to any 1200. The original Okrasa kit was sold way back in the 50's so way b4 the D type case.
have fun with the extra oomph 
madness is in the eye of the beholder  |
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on December 15th, 2012 at 03:47 PM |
|
|
Those D 1200 Beetles were sold in Euro bugs well into the mid 80s.
The 70s onward 1200 blocks have the later dual relief oil system but still the old single port oil cooler, but the intake manifolds are still the old
flat 1200 style so the carbs would fit if they are 40hp 1200 pattern.
|
|
|
karmann54
Officially Full-On Dubber
Posts: 337
Threads: 87
Registered: November 4th, 2002
Member Is Offline
Location: Kangaroo Point, Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 20th, 2012 at 06:17 PM |
|
|
Well I've picked up the (partial) kit - riechert manifolds, correct jets etc for 28PCIs, linkage brackets, mounting studs etc. Just have to get two
28PCI carbs and make or buy a linkage arm. Riechert are still around so should be able to pick up the linkage arm from him.
I'll have to do something with the air cleaners as well. Being a ghia the decklid springs get in the way, that will be a trial and error thing I
think at the time. I'll post a photo when they turn up.
|
|
|
