| [ Total Views: 800 | Total Replies: 17 | Thread Id: 100228 ] |
|
|
 RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 20th, 2012 at 08:58 PM |
|
|
Silicon/rtv/permatex does it have a place in an engine?
I'm about to start putting my 2 litre back together and there seems to be a lot of disagreement on this subject. To some people it is evil and to
others a necessary part of any engine rebuild. I'd like to hear everybody's thoughts and experience.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 21st, 2012 at 07:50 AM |
|
|
I use an RTV sealant on the barrel base, no where else. The main problem with the product is it spews into the inside of the join and little bits can
get into the oil system.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 21st, 2012 at 10:31 AM |
|
|
High temp RTV for exhaust gaskets, i also use loctite 518 to join the case halves and loctite grey under the barrels.
|
|
|
RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 25th, 2012 at 02:16 PM |
|
|
What about around pushrod tubes and under the head stud washers. I have a couple of engines on my bench that both have silicon in these places, one
very carefully and neatly the other not so. Is it a good idea to use silicon in these spot or should it be unnessecary.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 25th, 2012 at 04:57 PM |
|
|
You do not need any silicon on the push rod tubes, i use the loctite grey under the four head stud flat washers and make sure that there is no excess,
always clean it off so it is under the washer only.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 25th, 2012 at 05:38 PM |
|
|
I use permatex on the case halves and pushrod seals. The seals is just a precaution as you can never tell how good the seals are gonna be these days.
madness is in the eye of the beholder  |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 26th, 2012 at 10:23 AM |
|
|
Buy the german one's and put them on dry, if they are silicon the sealant will not stick to them anyway, remember they are under compression.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 26th, 2012 at 12:42 PM |
|
|
| Quote: | Originally
posted by vwo60
Buy the german one's and put them on dry, if they are silicon the sealant will not stick to them anyway, remember they are under compression.
|
The ones I got from Mick's sure weren't German hence using a bit of sealant to help 
next time when I have more time to source parts I'll make sure they're German
madness is in the eye of the beholder |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 26th, 2012 at 03:29 PM |
|
|
I buy complete german gasket sets from pierside parts for $14.00.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 26th, 2012 at 10:35 PM |
|
|
| Quote: | Originally
posted by psimitar
The ones I got from Mick's sure weren't German hence using a bit of sealant to help
|
Wow, thats a surprise.....NOT
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 26th, 2012 at 11:01 PM |
|
|
| Quote: | Originally
posted by vwo60
I buy complete german gasket sets from pierside parts for $14.00.
|
Sweet That's going in the memory banks Ta
madness is in the eye of the beholder |
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 26th, 2012 at 11:04 PM |
|
|
| Quote: | Originally
posted by matberry
| Quote: | Originally
posted by psimitar
The ones I got from Mick's sure weren't German hence using a bit of sealant to help
|
Wow, thats a surprise.....NOT
|
Hmm, I'm noting a spot of sarcasm there
I've given up finding an Oz vendor for German quality gear at reasonable prices tho mainly the quality thing so make use of the euro exchange rate at
present
madness is in the eye of the beholder |
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 27th, 2012 at 08:05 AM |
|
|
I stock them, how many do you want?
There are also more than 1 German Elring kit available, the cheap $14 version from O/S won't have everything in it.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 27th, 2012 at 09:55 AM |
|
|
everything except the the rear main seal, the german one's are $4.50 extra.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 28th, 2012 at 12:21 AM |
|
|
| Quote: | Originally
posted by matberry
I stock them, how many do you want?
There are also more than 1 German Elring kit available, the cheap $14 version from O/S won't have everything in it.
|
Thanks Matt. I'm good at the mo but good to know these things for future reference. How many parts of german quality do you stock?
madness is in the eye of the beholder |
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 28th, 2012 at 07:51 AM |
|
|
| Quote: | Originally
posted by psimitar
Thanks Matt. I'm good at the mo but good to know these things for future reference. How many parts of german quality do you stock?
|
I presently have around $20 000 worth of stock, too much to list but ranging from pretty well all air-cooled service parts to a big range of Weber
jets to that hard to find type 4 rubber dipstick boot or Berg performance gear....... Obviously not everything German but best quality available.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 28th, 2012 at 04:28 PM |
|
|
| Quote: | Originally
posted by matberry
| Quote: | Originally
posted by psimitar
Thanks Matt. I'm good at the mo but good to know these things for future reference. How many parts of german quality do you stock?
|
I presently have around $20 000 worth of stock, too much to list but ranging from pretty well all air-cooled service parts to a big range of Weber
jets to that hard to find type 4 rubber dipstick boot or Berg performance gear....... Obviously not everything German but best quality available.
|
Cool. I'll PM ya when I'm in need then
madness is in the eye of the beholder |
|
|
fish26
A.k.a.: benito
Fahrvergnugen
Posts: 903
Threads: 38
Registered: July 13th, 2007
Member Is Offline
Location: sydney
Theme: UltimaBB Pro Grey
Mood: Ken awesome
|
| posted on January 1st, 2013 at 08:54 PM |
|
|
my way........
hone the pushrod tube seal mating surface, good quality seals and on dry, I like the aluminium sprung tubes the likes of JayCee, Scat.......ones with
the double o-ring
Permatex Aviation for a lot of machined surfaces
If you are going to use RTV please use sparingly
bitten by the bug..........several times
|
|
|
