| [ Total Views: 823 | Total Replies: 13 | Thread Id: 100804 ] |
|
|
 Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
 posted on February 8th, 2013 at 03:37 PM |
|
|
Slamming a '64 Bug
So I'm about to start the task of lowering my 64 bug. I have no experience with bugs but I think I have an idea of what I have to do.
Removing the plates is no issue for me, thats just bolts, levering etc (and watch for the spring plate release, haha).
The thing I'm trying to get my head around at the moment is the spines.
At this point in time the car is stock height, havent taken exact measurements yet but at a guess it looks around 20cm clearence.
I'd like the car around 8-10 cm clear when done, so going by a spline table I found on Airkewld, I need to rotate the outter splines by anticlockwise
2 clicks (or inner for 2 clicks clockwise for and extra 1cm)
Is it that simple? and at this height will I need to notch my spring plates?
Thank you!
Johnny
|
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 8th, 2013 at 03:40 PM |
|
|
Remember that I think min ground clearance is 100mm in most states.
there is a table, inside and outside have divfferent rations. so you can use a combination of inside and outside splies to move the arm exactly.
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
|
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 8th, 2013 at 03:47 PM |
|
|
| Quote: | Originally
posted by BiX
Remember that I think min ground clearance is 100mm in most states.
there is a table, inside and outside have divfferent rations. so you can use a combination of inside and outside splies to move the arm exactly.
|
Yeh QLD is 100mm, fully laden, so realistically I shoule be aiming for 13cm or so unloaded.
I am aware of this but I want a low car for the time being, I may raise it later down the track but for the meantime that is the height I want to
achieve.
I'm also unsure if that law applies as the bug is pre ADR and some cars come out lower than 100mm from factory (which is legal) so who are Queensland
Transport to say it wasnt that low from factory 
|
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 8th, 2013 at 03:48 PM |
|
|
Also, this is the table I am using: http://airkewld.com/wp-content/gallery/lowering-the-rear-end/splines.jpg
|
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 8th, 2013 at 10:07 PM |
|
|
So will the spring plates need to be notched at this height?
|
|
|
SunshineKarmann
Casual Dubber
Posts: 34
Threads: 6
Registered: December 19th, 2008
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: Always up for a chat
|
| posted on February 8th, 2013 at 11:15 PM |
|
|
Yep. Best to remove those bump stops too.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on February 9th, 2013 at 06:54 PM |
|
|
here's another lowering table for spline amounts
Lowering chart
100mm is minimum height but also you are not allowed to lower or raise more than a 1/3 the distance from bumpstop to chassis.
madness is in the eye of the beholder  |
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 10th, 2013 at 01:44 AM |
|
|
Awesome, Thanks very much guys, will be tackling it in the morning 
|
|
|
AndrewB
Seriously Crusin Dubber
Posts: 141
Threads: 19
Registered: June 18th, 2011
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: arghhbjfhbejrhfebf
|
| posted on February 11th, 2013 at 12:58 PM |
|
|
You need notched and extended spring plates if you want to go real low, or your rear end will keep you very busy trying to keep the thing straight,
and it will go through tires and bearings. lol.
What beam and tyres are you going to run?
dont think about the splines too much, you will get very confused, just measure.
|
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 11th, 2013 at 02:03 PM |
|
|
How much extension is required? Is it dire that this happens?
We ended up notching 1" out of the plates at the deepest point.
From the measurements I took it's dropped approx 6.5cm, and I havent driven it to get it all to settle and bed in, so i'm expecting a few more
centremeters.
|
|
|
AndrewB
Seriously Crusin Dubber
Posts: 141
Threads: 19
Registered: June 18th, 2011
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: arghhbjfhbejrhfebf
|
| posted on February 12th, 2013 at 09:01 PM |
|
|
yes. sight down the side, you will see the rear tires toe in, with unextended plates.
you should go search on the samba, all the lowering info you need is on there.
|
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 13th, 2013 at 09:22 AM |
|
|
I've been searching Samba and from what I can gather, 2 clicks will equate to needing a 1/2" extension. Does this sound correct?
|
|
|
AndrewB
Seriously Crusin Dubber
Posts: 141
Threads: 19
Registered: June 18th, 2011
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: arghhbjfhbejrhfebf
|
| posted on February 15th, 2013 at 12:47 PM |
|
|
yea that sounds right,
what tyre combo and front beam are you going with?
|
|
|
Allbones
Officially Full-On Dubber
Posts: 395
Threads: 58
Registered: July 5th, 2012
Member Is Offline
Location: Ipswich QLD
Theme: UltimaBB Pro Black
|
| posted on February 18th, 2013 at 10:46 AM |
|
|
Running 16580r15 rear and 13580r15 front.
4" narrowed beam on the front (with shocks), 2.5" drop spindles and one set of caster shims under the bottom tube.
|
|
|
