| [ Total Views: 697 | Total Replies: 5 | Thread Id: 102428 ] |
|
|
 narumi
Seriously Crusin Dubber
I'll do it tomorrow
Posts: 138
Threads: 8
Registered: August 24th, 2011
Member Is Offline
Location: Adelaide, SA
Theme: UltimaBB Psyche Red
|
| posted on June 15th, 2013 at 02:10 AM |
|
|
Center Tie Rod (Super beetle)
I bought a center tie rod from overseas that goes from the box to the idler.
installed it on the car and it was making squeaky noise.
I thought it was the idler arm bush that was making noise.
but today I had a chance to look at it and took the idler arm off and turn out the tie rod was squeaking.
I proceed to use spray grease into the boot which seemed to help.
the noise is completely gone now after a short drive, steering is also lighter.
my question is arent all tie rod pre-greased, or did I get the bad one.
|
|
|
Uber Kafer
Wolfsburg Wizard
Posts: 414
Threads: 50
Registered: November 12th, 2009
Member Is Offline
Location: Bunbury (BunVegas) WA
Theme: UltimaBB Pro Blue ( Default )
Mood: Need a bigger shed..
|
| posted on June 15th, 2013 at 10:20 AM |
|
|
we assume some things, and grease from the factory would be one of them. I normally give the boot a bit of 'squish' test to check though. Might be
a good move to force some more grease in to yours, depending on what sort of grease you already sprayed in, and how much.
Just a thought.... if you got the part from the US, check that its not operating at some funny angle, ie at the limits of the tie rod end
rotation/travel and partially binding. I expect they are symmetrical and you have just flipped it, but without seeing it ??... I am just putting it
out there.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on June 15th, 2013 at 10:37 AM |
|
|
The drag link only fits one way and they are the exact same part LHD or RHD.
I suspect you may be right as the amount of people that complain their steering is heavy after replacing it suggests they are not shipped with enough
grease in them.
|
|
|
narumi
Seriously Crusin Dubber
I'll do it tomorrow
Posts: 138
Threads: 8
Registered: August 24th, 2011
Member Is Offline
Location: Adelaide, SA
Theme: UltimaBB Psyche Red
|
| posted on June 15th, 2013 at 10:44 AM |
|
|
I will have to pull the rods out again and change the boot i ruined aswell, don't know if I should use more lithium grease or HTB
|
|
|
Lucky Phil
Wolfsburg Wizard
Posts: 480
Threads: 16
Registered: August 1st, 2010
Member Is Offline
Location: Adelaide SA
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm a legend in my own lunchtime!
|
| posted on June 16th, 2013 at 09:47 PM |
|
|
Good question.
The Litium grease these days seems to be cr@p and seperates very quickly. I don't like it.
HTB seems to hold together better.
|
|
|
narumi
Seriously Crusin Dubber
I'll do it tomorrow
Posts: 138
Threads: 8
Registered: August 24th, 2011
Member Is Offline
Location: Adelaide, SA
Theme: UltimaBB Psyche Red
|
| posted on June 17th, 2013 at 12:56 AM |
|
|
@Joel I doubt this one come with grease at all haha.
I sprayed the grease on when i put in new brake rotor (ebay RDA slotted rotor{because it was cheaper than non slotted})
now that I no longer have squeaky steering noise. I have brake noise lol
hopefully goes away once bedded in.
|
|
|
