| [ Total Views: 784 | Total Replies: 13 | Thread Id: 102638 ] |
|
|
 FROSTY
Insano Dub Head
Posts: 744
Threads: 65
Registered: May 11th, 2009
Member Is Offline
Location: Palm Beach Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 3rd, 2013 at 07:42 PM |
|
|
How to shorten a clutch cable?
Hi There, just in the final stages of getting the drag car finished and I need to shorten the/a clutch cable. The peddles are now about 70mm back from
where they would normally be. I have a bit of a tube over the end ( temporary) till I can sort it.
Thanks
Jason
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on July 3rd, 2013 at 07:55 PM |
|
|
Hi
Do you have anybody up there that makes cables from scratch? Or maybe a boat place could crimp an end on for you.
I use a place in Sydney called Conwire, maybe they could make one and sent it up http://www.conwire.com.au/
Steve
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on July 3rd, 2013 at 08:43 PM |
|
|
You need a chandeler, someone who makes cables for yachts etc, they can fit a new end to the cable
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
silver
Veteran Volks Folk
Dangerous when poked
Posts: 2169
Threads: 162
Registered: December 8th, 2002
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: In 2 Minds
|
| posted on July 3rd, 2013 at 08:43 PM |
|
|
I did this for a shortened buggy pan
snip the cable, ream the fork clean (pedal end) of the old cable, and sweat (braze) in the cable again
Keeping it real !
|
|
|
whathaveidone
Custom Title Time!
Posts: 1559
Threads: 98
Registered: February 24th, 2010
Member Is Offline
Location: Dapto
Theme: UltimaBB Pro Blue ( Default )
Mood: Heading for 10.99
|
| posted on July 3rd, 2013 at 08:52 PM |
|
|
I can do it for you but you would have to get it down to me. I have the press with the dies at work. would just have to get an end fitting. If there 3
or 4mm thats no problem
|
|
|
Special Air Service
Custom Title Time!
Chief "Gunna"
Posts: 1769
Threads: 210
Registered: October 4th, 2004
Member Is Offline
Location: Old Bar , Mid North Coast , NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: In desperate need of a decent sleep
|
| posted on July 3rd, 2013 at 09:03 PM |
|
|
clutch cable shortening kit for sale here
http://forums.aussieveedubbers.com/viewtopic.php?tid=102635
not sure how this works but.
scroll down a fair way
[size=5] Calling all NSW Mid North Coast Veedubbers
Click Below [/size]
[size=6]Mid North
Coast VW [/size] |
|
|
FROSTY
Insano Dub Head
Posts: 744
Threads: 65
Registered: May 11th, 2009
Member Is Offline
Location: Palm Beach Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 3rd, 2013 at 09:29 PM |
|
|
Thanks guys. How does one of the shortening kits work???
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on July 4th, 2013 at 12:27 PM |
|
|
| Quote: | Originally
posted by FROSTY
Hi There, just in the final stages of getting the drag car finished and I need to shorten the/a clutch cable. The peddles are now about 70mm back from
where they would normally be. I have a bit of a tube over the end ( temporary) till I can sort it.
Thanks
Jason
|
Hi Jason
You can buy cable shorteners ??
hard to explain what they are..
made from a flat piece of steel bent over at each end to put the cable into, and in the centre, is a threaded piece with a thumb wheel..
You turn the thumb wheel and the threaded piece moves onto the cable and pushes it upwards.. to shorten the cable..
they are really made for adjustment and not sure it would go 70mms?
maybe there are different sizes, but it IS extra weight for your drag car..
the quick way which I have seen, is cut the cable and put them side by side for about 100mm and use wire clamps to tie them together..
just get the correct clamps for your wire.. they work good..
but are again extra weight.. lol but they are cheap and good to adjust your clutch / pedal etc..
:LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 4th, 2013 at 03:56 PM |
|
|
| Quote: | Originally
posted by 68AutoBug
| Quote: | Originally
posted by FROSTY
Hi There, just in the final stages of getting the drag car finished and I need to shorten the/a clutch cable. The peddles are now about 70mm back from
where they would normally be. I have a bit of a tube over the end ( temporary) till I can sort it.
Thanks
Jason
|
Hi Jason
You can buy cable shorteners ??
hard to explain what they are..
made from a flat piece of steel bent over at each end to put the cable into, and in the centre, is a threaded piece with a thumb wheel..
You turn the thumb wheel and the threaded piece moves onto the cable and pushes it upwards.. to shorten the cable..
they are really made for adjustment and not sure it would go 70mms?
maybe there are different sizes, but it IS extra weight for your drag car..
the quick way which I have seen, is cut the cable and put them side by side for about 100mm and use wire clamps to tie them together..
just get the correct clamps for your wire.. they work good..
but are again extra weight.. lol but they are cheap and good to adjust your clutch / pedal etc..
:LEE
|
Lee, they talking about cable shorteners like these
http://www2.cip1.com/ProductDetails.asp?ProductCode=ACC-C10-2568
You could also try this setup? It halves the pedal effort too.
http://www.thesamba.com/vw/forum/viewtopic.php?t=515615&highlight=clutch+...
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
FROSTY
Insano Dub Head
Posts: 744
Threads: 65
Registered: May 11th, 2009
Member Is Offline
Location: Palm Beach Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 4th, 2013 at 06:15 PM |
|
|
Hey thanks smiley, that pulley set up is unreal. I wonder if anyone here has used one?
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on July 4th, 2013 at 07:04 PM |
|
|
| Quote: | Originally
posted by FROSTY
Hey thanks smiley, that pulley set up is unreal. I wonder if anyone here has used one?
|
I'm not sure. They would be great for a heavy clutch.
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
FROSTY
Insano Dub Head
Posts: 744
Threads: 65
Registered: May 11th, 2009
Member Is Offline
Location: Palm Beach Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 27th, 2013 at 07:04 PM |
|
|
Hi There,
I have been trying all sorts of things to shorten the cable and the two clamp idea was ok but just looked dodgy. I found at a stainless wire suplier a
clamp that is used on a balustrade (handrail) it works fine and time will tell if it lets go. (has to be pretty strong to stop someone falling through
a verandah etc.)
Thanks
jason
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
bugzla
Custom Title Time!
Posts: 1164
Threads: 240
Registered: June 9th, 2007
Member Is Offline
Location: townsville
Theme: UltimaBB Pro Blue ( Default )
Mood: always happy
|
| posted on July 27th, 2013 at 08:24 PM |
|
|
why not take the cable length to someone that does cables ie brake shops
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on July 27th, 2013 at 10:28 PM |
|
|
| Quote: | Originally
posted by bugzla
why not take the cable length to someone that does cables ie brake shops
|
+1
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
