| [ Total Views: 507 | Total Replies: 4 | Thread Id: 103469 ] |
|
|
 takis
Seriously Crusin Dubber
Posts: 106
Threads: 27
Registered: August 27th, 2007
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 15th, 2013 at 11:34 AM |
|
|
Front transmission mount which way around.?
Engine has been removed , front mount was delaminates, so thanks to those who pointed me in the right direction.
About to install new nosecone mount, but I noticed the mount has a dimple. does this signify a need to be mounted a specific orientation?
If so , where does the dimple go? Up, or down?
Many thanksj,
Peter.
|
|
|
takis
Seriously Crusin Dubber
Posts: 106
Threads: 27
Registered: August 27th, 2007
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 15th, 2013 at 03:30 PM |
|
|
So I inserted the mount cutout up. There is a web from the nose cone of the gearbox that looks like needs the room from the cut out.so new mounts have
been installed throughout, I also installed a cross bar that bolts onto the gearbox and has urethane blocks resting on the shoehorns.this is meant to
help the front mount .
Well I have done it, very happy with the job. Now do some odd bits and pieces on the motor and in it will go and back on the road shortly.
Thanks for listening to my ramblings.
Peter.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on September 15th, 2013 at 03:32 PM |
|
|
I just looked at a manual and they showed it had two studs or bolts and they could only go on one way onto the gearbox...
LHS bolt was higher than the RHS bolt...
O
............ O
so could only go one way... later mounts had slots...
not sure on early mounts...
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on September 15th, 2013 at 07:01 PM |
|
|
| Quote: | Originally
posted by 68AutoBug
I just looked at a manual and they showed it had two studs or bolts and they could only go on one way onto the gearbox...
LHS bolt was higher than the RHS bolt...
O
............ O
so could only go one way... later mounts had slots...
not sure on early mounts...
LEE
|
When you flip them upside down the studs are all still in the same orientation.
The front mounts after split cases stopped sit the same way this one is
|
|
|
takis
Seriously Crusin Dubber
Posts: 106
Threads: 27
Registered: August 27th, 2007
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 15th, 2013 at 10:14 PM |
|
|
As Joel pointed out they can be inverted.
The offset on the bolts is the same whichever way you turn them.
As I discovered I went notch up,,I hope it's correct too far now to go back.lol
|
|
|
