| [ Total Views: 1660 | Total Replies: 12 | Thread Id: 104341 ] |
|
|
 Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on December 10th, 2013 at 04:36 PM |
|
|
Plastigauge - Surprised its never been mentioned on here
Hi all,
Soon will be building a motor from scratch and did a search on here since the beginning and Plastigauge has never been mentioned.
What are you top engine builders using today to check bearing clearances of rods and crank bearings.
Is there there a new way of checking this now, as I am old school and used plastigauge years ago for this sort of thing.
Cheers, Kev
For those that don't know what I'm talking about CLICK HERE
|
|
|
coletrickle
Wolfsburg Wizard
Posts: 661
Threads: 34
Registered: April 22nd, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 10th, 2013 at 04:54 PM |
|
|
i use a "device"known to a few here as Craig Brown,aka crankshaft engineering.
|
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on December 10th, 2013 at 04:58 PM |
|
|
| Quote: | Originally
posted by coletrickle
i use a "device"known to a few here as Craig Brown,aka crankshaft engineering.
|
Thanks Cole,
so that the latest technology available 
Kev
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on December 10th, 2013 at 06:41 PM |
|
|
I use a micrometer much more accurate
take your pick imperial or metric
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on December 10th, 2013 at 07:26 PM |
|
|
Plastigauge works well and gives a accurate resalt, I mount the bearings in the case and measure them with a inside mic, the only problem is getting a
consistent resalt, I think Craig uses a internal bore gauge, I had him do my last engine as we ground the crank under .008" and renitrided it ,
measured the bearings and Finnish grinding the crank to size to suit the bearings, a lot of the bearings you buy now are not consistent in there size.
|
|
|
vduboy
Insano Dub Head
Posts: 702
Threads: 41
Registered: October 6th, 2012
Member Is Offline
Theme: UltimaBB Streamlined2
Mood: Dying to get more buggy building time..
|
| posted on December 10th, 2013 at 07:34 PM |
|
|
I use it all the time on my bike engines at work. Very quick and easy. I always double check with a mic though
It will all be OK in the end, if it's not OK it's not the end!
|
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on December 10th, 2013 at 08:36 PM |
|
|
Dave & vduboy,
I understand you can use a micrometer and measure the outside of the crank mains and rod journals, but this doesn't give you the gap between bearing
and journal. Think is is something like .001 to .003 thousands of an inch. I guess you could go off the size the bearing (shells) says it is, but is
that accurate enough to give 1-3 thou difference ?
Kev
|
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on December 10th, 2013 at 09:13 PM |
|
|
There are many methods to measure internal bores.
You can get inside mics, as well as snap gauges, or even inside callipers.
The best thing is a bore gauge though, set off the crank diameter.
I was spoilt working at Crankshaft Engineering with Sunnen brand bore gauges.
They measured down to ten thousandths of an inch, (.0001"),
so as soon as I could afford it,
I got some of my own,
but still use my inside mics for odd jobs,
and sometimes even snap gauges and inside callipers for other odd jobs that don't allow access.
Plastigage is better than not checking at all, and is the most affordable for the novice.
but unless you can remove the rod half, or case half, without squishing the material,
then you can easily get a false reading.
The ultimate way to prepare any engine is to grind the crank, to give even and correct oil clearance,
measured off the mounted bearings.
For all my engines I begin by machining the conrod, and crank case tunnels to the minimum tolerance for maximum crush,
and then measure the mounted bearings.(torqued all bolts to spec)
From here I have the crank ground to achieve the ideal oil clearance for the application.
Most times I do as Shayne had done,
and have the crank shaft pre-ground, then nitride, and finally ground to the desired clearance.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on December 10th, 2013 at 10:06 PM |
|
|
+1 for bore gauge.
I tried plastigauge, its a good indicator but far from precise. I'd say use it for a rebuild, but not for new parts (which haven't been
trialled/tested). My new crank was so out of whack, pastigauge just made it more confusing as i got inconsistent results across all journals. But if
it was from a motor that had been running prior, tried and tested, it was indicate well any excess clearance.
1 tried snap gauges and a micrometer on teh big ends and mains. It gave a great reading but made a mess sliding over the surface of the bearings. Had
to get a new set as even with a coat of coil it scratched the surfaces. I couldn't afford a bore gauge, so dropped it all to crankshaft engineering
for clearance checking by the time i go to my third set of big ends and second set of mains.
I did however use plastigauge for the cam bearings, and the clearances checked out. was a very easy test  . and teh cam is spinning nicely!
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on December 11th, 2013 at 08:04 AM |
|
|
I'm another for Crankshaft Engineering, plastigauge is not precise enoudh for me, but good for a guide if necessary.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
kylandpl
Casual Dubber
Posts: 24
Threads: 5
Registered: December 30th, 2008
Member Is Offline
Location: Central Coast, NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 20th, 2013 at 10:21 AM |
|
|
Hey Kev,
When I went looking for Plastigauge about 5 years ago, the parts guy said he hadn't had anyone ask for that for about 10 years!
He did manage to get some in for me, but it was a "special order"!
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on December 20th, 2013 at 11:28 AM |
|
|
Repco had it in stock
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on December 20th, 2013 at 01:26 PM |
|
|
| Quote: | Originally
posted by kylandpl
Hey Kev,
When I went looking for Plastigauge about 5 years ago, the parts guy said he hadn't had anyone ask for that for about 10 years!
He did manage to get some in for me, but it was a "special order"!
|
I read this and just laughed Obviously showing my
age and my older ways 
Thanks, Kev
Merry Christmas to all 
|
|
|
