| [ Total Views: 691 | Total Replies: 8 | Thread Id: 106877 ] |
|
|
 x275
Commited Dubber
Posts: 61
Threads: 19
Registered: March 3rd, 2013
Member Is Offline
Theme: UltimaBB Pro Black
|
| posted on August 14th, 2014 at 10:06 PM |
|
|
Information for lowering my 71 super rear end
Just looking for some advise and/or some instructions on what I need to do to lower the rear of my 71 super
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on August 16th, 2014 at 05:11 PM |
|
|
Same as a swing axle bug tho rear wing removal does make the job easier.
Do you have a workshop manual? Is the engine/gearbox/interior still fitted to the vehicle?
madness is in the eye of the beholder  |
|
|
x275
Commited Dubber
Posts: 61
Threads: 19
Registered: March 3rd, 2013
Member Is Offline
Theme: UltimaBB Pro Black
|
| posted on August 16th, 2014 at 10:55 PM |
|
|
Yeah i have a workshop manual and the car is a runner.
It's stock height and want to bring it down 2 inches in the rear. Seems like the drivers side sits a tad higher than the passengers does..
|
|
|
Aussie Dubbin
Fahrvergnugen
Posts: 895
Threads: 90
Registered: July 21st, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 17th, 2014 at 08:07 AM |
|
|
A simple description.
Put the rear on stands. Remove wheels and diagonal arms away from swing plates. May find it easier to undo the 17mm hex bolt holding the diagonal arm
in.
Loose the guard about the first 4 or so bolts to give you better access.
Undo the swing arm cap and remove. At this point the swing arm can swing down so be aware it wants to do that under pressure. It doesn't want to move
upwardso this should always be your safe working area. (Above)
Lever the swing arm off its stop. Choose your method. Pry bar or hammer. If it is a twin plate you can easily lever from both ends. Remember don't go
below the swing arm!
|
|
|
Aussie Dubbin
Fahrvergnugen
Posts: 895
Threads: 90
Registered: July 21st, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 17th, 2014 at 08:14 AM |
|
|
On e it's loose don't remove from its location just make sure it's fully down and mark the original position.
At this point do the otherside to.
Setting is up or down from there. I always use trial and error to set height. Just make sure the two sides are the same.
Putting them back in is easier with longer bolt in the cap. Put 3 in. Jack the arm up and onto it's stop. Then put the forth bolt in. Do up bolts
till you can replace with original. One at a time.
|
|
|
x275
Commited Dubber
Posts: 61
Threads: 19
Registered: March 3rd, 2013
Member Is Offline
Theme: UltimaBB Pro Black
|
| posted on August 17th, 2014 at 08:41 AM |
|
|
Ok thanks for the advice, I'll put the car up this arvo and sus it out.
Cheers
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on August 17th, 2014 at 01:13 PM |
|
|
If you think the rear suspension isn't level then you need to measure on a flat surface to the underside of the torsion bar tube. This will let you
know if it is the suspension. Could be a weaker torsion bar or a previous owner tried adjusting the rear but didn't quite get it right.
Use this website to help figure out the correct number of inner and outer splines required to level the rear. Beetle Rear lower spline guide
madness is in the eye of the beholder |
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on August 17th, 2014 at 01:52 PM |
|
|
http://forums.aussieveedubbers.com/viewtopic.php?tid=78303
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
x275
Commited Dubber
Posts: 61
Threads: 19
Registered: March 3rd, 2013
Member Is Offline
Theme: UltimaBB Pro Black
|
| posted on August 18th, 2014 at 08:34 AM |
|
|
Thanks for that, that's extremely helpful.
|
|
|
