| [ Total Views: 530 | Total Replies: 4 | Thread Id: 107662 ] |
|
|
 BeigeSav1969
Casual Dubber
Posts: 32
Threads: 13
Registered: August 14th, 2014
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: Perplexed
|
| posted on November 17th, 2014 at 04:40 PM |
|
|
seats hard to fit on new floorpan 69 Bug
Hey folks,
As the title says we've installed a new floor pan o a 69 bug and tried a test fit of the original drivers seat on the new rails. While I can get it
on they are binding and not sliding smoothly at all. Also appears that the drivers seat is a fair amount closer to the side (heater channel) than it
used to be.
Is it common to have to make some sort of adjustment to the rails?
Any suggestions would be much appreciated.
Cheers Ryan
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on November 17th, 2014 at 05:25 PM |
|
|
give them a few taps inwards length of wood and hammer little at a time
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on November 18th, 2014 at 06:08 PM |
|
|
Check the floor runners are parallel and dead straight. Any ripple in the runner will cause binding. Check the seat runner isn't kinked anywhere.
Inner floorpan runner is only about 20mm from the tunnel at the front end of the runner. I believe it tapers out from the tunnel towards the rear of
the vehicle to angle the seat to the pedals but been a while since I've looked at my stripped pan so could be wrong on the tapering but not how close
it sits at the front edge.
madness is in the eye of the beholder  |
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 18th, 2014 at 06:29 PM |
|
|
Can you put some pics up of the floor pan runner as well as the bottom of the seat guides.I have just cut a 6 volt floor pan for a Buggy and tried to
fit some seats from a 12 volt car.they both use a guide and runner set up- but the later seats have a much wider guide, but they bind on the early
pan.On the later pans, they had a nylon guide that ran inside the seat guide.I had to cut and shut my seats by fitting the early seat guides to the
later seats.
|
|
|
BeigeSav1969
Casual Dubber
Posts: 32
Threads: 13
Registered: August 14th, 2014
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: Perplexed
|
| posted on November 18th, 2014 at 10:14 PM |
|
|
Thanks for the replies fellas, I'll give all that's been suggested a go, just about to fit the headliner and the last thing I need is to be
wrestling with stubborn seats and damage anything already done interior wise in anger LOL.
Give me a few days ndturbo and I'll get some pics for you.
Thanks again, I'll update with my impending success story.
|
|
|
