| [ Total Views: 2814 | Total Replies: 20 | Thread Id: 108638 ] |
|
|
 hpnotch
Seriously Crusin Dubber
Posts: 133
Threads: 28
Registered: November 11th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 21st, 2015 at 05:21 PM |
|
|
Oil Temp gauge
Hi everyone
I am thinking about installing an oil temp gauge in my notch, but I am not sure how i would attach the sender unit.
I have heard that the oil pressure relief plug is a good spot - what and where is it?
The other option is fit it to the oil drain cover - are these sold with an additional threaded slot to take the sending unit?
Or is this more trouble than it's worth?
Any advice appreciated.
Thanks in advance.
|
|
|
Lo-tech
Casual Dubber
Posts: 43
Threads: 13
Registered: November 28th, 2010
Member Is Offline
Location: Down the Bay, sort of
Theme: UltimaBB Pro Blue ( Default )
Mood: Delusionally optimistic
|
| posted on April 13th, 2015 at 01:59 AM |
|
|
I've used a dipstick sender in the Kombi for years - no drilling the case, and works fine. Keep your original dipstick for spot-on oil level
readings, however. No experience with other methods, but the plug for the pressure relief plunger is a coin-sized disc with a big screwdriver slot in
it. Get under your engine and you'll see two of them, left-hand side of case, one @ flywheel end, one @ pulley end. One's a relief plunger (pulley
end), the other one's a pressure control plunger (flywheel end). I haven't bothered with an oil temp gauge in my Type 3, but if I did a lot of
highway work in it, I'd be tempted. If it saves your engine once by warning you when to back off the throttle on a 44C day, it's more than paid for
itself.
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 13th, 2015 at 07:59 AM |
|
|
Use a sump plug sender. The most accurate of them all. Simply pull out your old sump plug and put in this one! The dipstick is only at one end of the
engine whereas the sump plug is at the bottom so it gets a constant reading.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on April 13th, 2015 at 08:02 AM |
|
|
Either dipstick as mentioned or relief valve plug.
| Quote: | Originally
posted by adlbeetle66
Use a sump plug sender. The most accurate of them all..
|
actually they are one of the worst spots.
Drain plug senders are problematic, they hang down susceptible to damage, they have to be a special shallow sender to suit vws or they crush the
bottom of the strainer over the oil pickup tube and they read low and not accurate.
they are not accurate because the road draft underneath has a cooling effect on the sender and gives a low reading, has been shown to be upto 35c off
compared to other locations.
Relief valve is on the lower left like so
|
|
|
hpnotch
Seriously Crusin Dubber
Posts: 133
Threads: 28
Registered: November 11th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 13th, 2015 at 08:41 AM |
|
|
Thanks to everyone for the advice - much appreciated.
I have purchased a sender unit from Mick motors so I am assuming it's a shallow type. They had suggested the sump plug position, and it does seem a
simple job to perform. i am not too concerned about accuracy - I've been told most gauges do not not accurately reflect engine temp - but they are
beneficial as a sudden fluctuation in temp would indicate a problem.
However, I agree oil relief position does seem more secure.
Do you know if the sender I bought can fit in either position - or are different units (with different threads) required ?
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 13th, 2015 at 08:43 AM |
|
|
I bought mine from Micks too.
VDO ?
I was going to ask the same question, if the relief position is more secure can you use the same one?
Joel?
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on April 13th, 2015 at 09:02 AM |
|
|
Different thread unfortunately, drain plug is M14, relief valve plug is M18
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 13th, 2015 at 09:08 AM |
|
|
Oh. Can you get one specially for the relief then?
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 13th, 2015 at 09:09 AM |
|
|
There is an adapter available from CB (I have some in stock at present) that uses the sump plug in the oil pressure sender location (adapts both
senders into one hole), I find it a good way to utilize the old sender in a much better/more accurate reading location
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 13th, 2015 at 09:10 AM |
|
|
How much do you charge for them Matt?
On here or email 
|
|
|
donn
Wolfsburg Elder
Posts: 3515
Threads: 428
Registered: November 30th, 2005
Member Is Offline
Location: NEWCASTLE NSW
Theme: UltimaBB Pro Blue
Mood: LAID BACK AND CONFUSED
|
| posted on April 13th, 2015 at 10:41 AM |
|
|
| Quote: | Originally
posted by adlbeetle66
How much do you charge for them Matt?
On here or email
|
On here please or PM, watching with interest
I dream of a day when a chicken can cross a road without being asked for it's motive!
|
|
|
hpnotch
Seriously Crusin Dubber
Posts: 133
Threads: 28
Registered: November 11th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 13th, 2015 at 11:24 AM |
|
|
X3 Thanks Matt
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 13th, 2015 at 02:54 PM |
|
|
Oh!!
Looks like I only have one left and it's spoken for on the job presently in, sorry about that. I'll be getting more or maybe Vintage or RPR have
them ???
CB part # 2355 if you want to go look for them
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
hpnotch
Seriously Crusin Dubber
Posts: 133
Threads: 28
Registered: November 11th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 13th, 2015 at 04:19 PM |
|
|
No problem! - thanks for the earlier advice.
|
|
|
d3wy
Casual Dubber
Posts: 23
Threads: 6
Registered: October 30th, 2014
Member Is Offline
Location: Newcastle, NSW
Theme: XMBX Pro Green
|
| posted on April 13th, 2015 at 11:29 PM |
|
|
Will this (Ebay Link - VDO Oil
Temp Sender 300F/150C M18 X 1.5 # V323-064) work in the releive valve location?
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 14th, 2015 at 08:02 AM |
|
|
Yes, that will work as it is an M 18 thread. Great find there 
|
|
|
d3wy
Casual Dubber
Posts: 23
Threads: 6
Registered: October 30th, 2014
Member Is Offline
Location: Newcastle, NSW
Theme: XMBX Pro Green
|
| posted on April 14th, 2015 at 09:03 PM |
|
|
Any one have any Suggestions for a decent guage to pair with the sensor I linked above?
And it says it's an oil sender, therefore my understanding is temp and pressure, will it support both features or just one?
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on April 14th, 2015 at 09:04 PM |
|
|
Im using SAAS gauges, but there is Auto Meter, and many other trusted brands out there.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on April 14th, 2015 at 09:53 PM |
|
|
I would stick with VDO gauges, the likelyhood of finding a different brand gauge with that same Ohm range aren't good but if you do mix and match do
the boiling water test with it first so you can get an idea of how accurate it is.
|
|
|
hpnotch
Seriously Crusin Dubber
Posts: 133
Threads: 28
Registered: November 11th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 10th, 2015 at 02:22 PM |
|
|
OK - I have now got myself another sender with the M18 thread to suit the relief valve location.
I read here http://www.vw-resource.com/oiling_system.html
that it is important to replace the plug at the relief valve not the pressure control valve.
Can someone please confirm that correct plug to replace is at the fan end of the type 3 motor?
Are there any tricks to removing the plug - should I drain the motor first? (otherwise if I remove with a full load of oil will oil pour from
the plug?)
thanks in advance
|
|
|
Blue65
A.k.a.: Yau
Officially Full-On Dubber
Posts: 298
Threads: 93
Registered: September 30th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: Retrospective
|
| posted on April 25th, 2016 at 12:17 AM |
|
|
Has anyone used the oil temperature gauge from savemybug.com
http://savemybug.com/about.htm
It looks simple and straight forward to install
______________________
Owner of a 1964 VW Beetle, 1641cc engine, etc..
|
|
|
