| [ Total Views: 738 | Total Replies: 8 | Thread Id: 109018 ] |
|
|
 waaagh
Casual Dubber
Posts: 32
Threads: 11
Registered: September 25th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 12th, 2015 at 09:27 AM |
|
|
Chasing info on fitting Weld Rodlite wheels
I've seen a few pictures of bugs running weld wheels (namely in the drag forums). I really like the look of weld rodlites and would like to fit a set
to my 63.
How do people go about changing the stud pattern on the earlier bugs? Is it just a case of changing over to disc brakes (I don't think discs would
clear these wheels), or are they using ford/holden brake components mated to vw mounts?
Anybody know?
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on May 12th, 2015 at 09:36 AM |
|
|
got a photo of the wheel?
"If at first you don't succeed, skydiving is not for you." - Anonymous  |
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on May 12th, 2015 at 10:42 AM |
|
|
http://www.summitracing.com/int/parts/wld-93-55346/overview/
|
|
|
waaagh
Casual Dubber
Posts: 32
Threads: 11
Registered: September 25th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 12th, 2015 at 10:52 AM |
|
|
https://s-media-cache-ak0.pinimg.com/736x/ae/a7/8d/aea78d2c6524c3f34ca450c6e2...
This is what I'm after.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on May 12th, 2015 at 12:25 PM |
|
|
You will have to change the drums to discs on the front with the correct stud pattern, at the rear a set of blank 4 stud drums drill to the correct
stud pattern, depends on the ET of the wheel if it will fit under the car.
|
|
|
waaagh
Casual Dubber
Posts: 32
Threads: 11
Registered: September 25th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 12th, 2015 at 02:09 PM |
|
|
Front disc brakes won't have clearance issues?
|
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on May 12th, 2015 at 06:50 PM |
|
|
Those wheels are more commonly used on HQs or XDs, and they have no disc rotor clearance issues with the stock 11" rotors (same as VW Beetle
basically) and even with smaller 14" wheels, so you should be fine.
You could also just get new drums both front and rear, re-drill to 5 x 4.5" Ford, then bolt them up. That will also allow you to run Tojo 5-stud rims
off anything from a Corolla or Camry all the way up to whizz-bang Supra stuff, they have the same wheel pattern.
The link to Summit I gave shows a 15 x 5" rim with 3.5" backspace, so compared to a stock VW 15 x 4.5" it will stick out 1/2" more, with the same
amount of rim inside, so no clearance issues there either. You can even run a stock 165/80R15 on a 5" rim if you want, or go all the way up to a 195
with no problems.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on May 12th, 2015 at 07:06 PM |
|
|
You cannot drill the original drums from a link pin car for that stud pattern.
|
|
|
waaagh
Casual Dubber
Posts: 32
Threads: 11
Registered: September 25th, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 13th, 2015 at 09:33 AM |
|
|
Awesome. Thanks a lot for the help and info.
|
|
|
