| [ Total Views: 942 | Total Replies: 5 | Thread Id: 111536 ] |
|
|
 beatman11
Commited Dubber
Posts: 64
Threads: 15
Registered: January 27th, 2014
Member Is Offline
Location: Canberra
Theme: UltimaBB Pro Grey
Mood: Happy
|
| posted on September 7th, 2016 at 12:35 PM |
|
|
drum brake backing plate thickness
Hi All,
I am wanting to know the thickness of a drum brake backing plate (where it bolts between the axle and bearing cap cover/holder) for a 63 beetle.
The reason is I have an oval beetle with empi rear disc brakes (don't laugh they were on the car when I bought it) and there is a lot of slop where
the axle bearing sits (in and out) I think I have the wrong bearing caps fitted as per note on the sparse empi fitting instructions I found online -
does anyone have empi rear discs fitted on a pre 60 beetle - what bearing caps are you using?
Cheers
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on September 7th, 2016 at 05:32 PM |
|
|
Pretty sure they are 5mm thick at the mounting face.I have done rear disc brake conversions using ED Falcon bits- I reckon the Falcon stuff is 6mm, so
I had to mill 1 mm from the caliper bracket- been a while though
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on September 8th, 2016 at 02:48 PM |
|
|
Yea, about 5mm in total. Not surprised the Empi bracket is renowned for flexing cos 5mm for a caliper bracket is worthy of VolksConversions.
Anyway, are you sure it's the bearings moving? it's normally a pretty tight fit in the tube hub and bearing cap. If definitely the beaing moving
then you'll have to get a wider outer spacer made plus a shim for the inside of the bearing cap.
madness is in the eye of the beholder  |
|
|
Old Dubber
Wolfsburg Wizard
Posts: 605
Threads: 25
Registered: August 26th, 2002
Member Is Offline
Location: Everton Hills, Brisbane, QLD, Australia 4053
Theme: UltimaBB Pro Blue ( Default )
Mood: great!
|
| posted on September 9th, 2016 at 08:54 AM |
|
|
Just measured my set at 5mm
|
|
|
beatman11
Commited Dubber
Posts: 64
Threads: 15
Registered: January 27th, 2014
Member Is Offline
Location: Canberra
Theme: UltimaBB Pro Grey
Mood: Happy
|
| posted on September 9th, 2016 at 11:57 AM |
|
|
Awesome thankyou for the info guys - the empi caliper plate is 6mm - so there is problem number one for me - off to find a milling machine. Then I
will see if I have the correct bearing caps next
Cheers
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on September 9th, 2016 at 01:41 PM |
|
|
| Quote: | Originally
posted by beatman11
Awesome thankyou for the info guys - the empi caliper plate is 6mm - so there is problem number one for me - off to find a milling machine. Then I
will see if I have the correct bearing caps next
Cheers
|
Even 6mm is pretty thin for a caliper bracket.
As far as I'm aware there is only Swing and IRS type of bearing cap. I think IRS outer bearing is thicker than the SA bearing. So IRS cap may be
deeper but if you had it fitted to a swing then the outer spacer would sit inboard of the bearing seal and make your axle tube leak like crazy.
madness is in the eye of the beholder |
|
|
