[ Total Views: 1265 | Total Replies: 5 | Thread Id: 22804 ] |
|
syncro
Seriously Crusin Dubber
Posts: 103
Threads: 27
Registered: August 30th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: spacey
|
posted on May 12th, 2004 at 08:54 AM |
|
|
Extending rear trailing arms for T3 Syncro?
Some Syncros came with 16" wheels, to fit these in, the rear trailing arms were extended to alow extra clearence between the tire and trailing arm.
There is a place in Canada making moddified, +25mm, trailing arms but the cost is high once landed here in Aust.
I'm wondering if any one knows of an engineer that has or could make this modification so I can put some 16's on my syncro.
Steve
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
posted on May 12th, 2004 at 09:43 AM |
|
|
Dyno - one of the Qld buggy boys, has made some custom trailing arms for various buggys. I'm not sure how to get hold of him, but Brad or any of the
radical sand blasters up North should be able to put you onto him.
Kruizin Kol
|
|
Brad
Wolfsburg Elder
Posts: 3764
Threads: 332
Registered: August 24th, 2002
Member Is Offline
Location: SE QLD, Mt Nebo
Theme: UltimaBB Pro Blue ( Default )
Mood: Manx Buggy Building
|
posted on May 12th, 2004 at 11:37 AM |
|
|
Contact Custom Offroad as they may make them. I have never seen longer T3 arsm as they are nothing like the others.
|
|
syncro
Seriously Crusin Dubber
Posts: 103
Threads: 27
Registered: August 30th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: spacey
|
posted on May 12th, 2004 at 12:43 PM |
|
|
thanks for the replies,
I will give them a call.
to have a look at some ---fast forward
the 225/75/16 tyres I want to put on will fit but it only leaves a few mm of clearence at the apex of the arm!
Steve
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
posted on May 12th, 2004 at 04:40 PM |
|
|
I've got about 8mm clearance to the trailing arms on my kombi with 238/85-16's..... they haven't scraped yet! Too bad if I want to fit chains
though....
Kruizin Kol
|
|
syncro
Seriously Crusin Dubber
Posts: 103
Threads: 27
Registered: August 30th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: spacey
|
posted on May 14th, 2004 at 08:58 AM |
|
|
I gave George at Custom Offroad a call and got a straight 'no, can't do it and dont know who could'.
Any other ideas or suggetions?
Steve
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
posted on May 14th, 2004 at 11:35 AM |
|
|
Steve, are they nearly rubbing on the tread or the sidewall? Maybe you could looking for different sized tyres to give you more clearance?
I don't know if the following sizes are even produced, but for the sake of an example: a 205/85-16 (narrower but taller) would give you more side
clearance, or a 255/65-16 would give you a bigger contact patch, with a slightly smaller O.D.
I've found that some tyre places will chuck a 2nd hand tyre on a rim so you can check the fit, and remove it again, for minimum cost (say $10-20). My
guy even does it for free!
I don't know if this helps, but it's the only suggestion I could think of. It would probably be cheaper than custom trailing arms too, unless you
can find a longer pair at the wreckers somewhere locally....
Kruizin Kol
|
|
type2nut
Officially Full-On Dubber
Posts: 223
Threads: 39
Registered: January 22nd, 2003
Member Is Offline
Location: Ceduna
Theme: UltimaBB Pro Blue ( Default )
Mood: sandy
|
posted on May 22nd, 2004 at 08:42 AM |
|
|
Steve,
this thread is worth reading:
http://autos.groups.yahoo.com/group/Syncro/message/21272
What 16" wheels are you fitting?
Also, your mate who bought the spare wheel carriers in from Bernd in Germany - is he happy with them? And do you know how long they took to get to him
once he ordered them?
Cheers,
Andy
|
|