| [ Total Views: 424 | Total Replies: 3 | Thread Id: 26240 ] |
|
|
 VolksFolks
A.k.a.: Pandy
Son of Jim - Creator of Good
Posts: 2869
Threads: 350
Registered: December 29th, 2003
Member Is Offline
Location: Tasmainac, Launceston, 7212
Theme: UltimaBB Pro Blue ( Default )
Mood: Proud DSK Contributor
|
| posted on July 21st, 2004 at 11:39 AM |
|
|
A Quicky Tech Q
What is the size of the large pushrod tube 'O' ring, the one that fits into the crankcase, is it 25mm or 1 inch, i canna remember, it is a 1800
motor
Thanks Andy
They laugh because You are different, You laugh because They are all the same.
check out http://www.lowlight.com.au for low lights only.. |
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 21st, 2004 at 01:17 PM |
|
|
as one inch = 25.4mm ther would be little difference and with production tolerances it shouldn't matter
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
|
|
|
VolksFolks
A.k.a.: Pandy
Son of Jim - Creator of Good
Posts: 2869
Threads: 350
Registered: December 29th, 2003
Member Is Offline
Location: Tasmainac, Launceston, 7212
Theme: UltimaBB Pro Blue ( Default )
Mood: Proud DSK Contributor
|
| posted on July 21st, 2004 at 01:21 PM |
|
|
so are they 25.4mm, i need to get replacements
Andy
They laugh because You are different, You laugh because They are all the same.
check out http://www.lowlight.com.au for low lights only.. |
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
| posted on July 21st, 2004 at 02:24 PM |
|
|
Make sure you get the German ones.... the cheaper varieties tend to go hard and leak prematurely. 
Kruizin Kol
|
|
|
Madeline
Learner Dubber
Posts: 11
Threads: 1
Registered: July 16th, 2004
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 21st, 2004 at 09:16 PM |
|
|
The inner ones (case side) are black & smaller.The outer ones (head side) are either red,green or yellow & are larger of the two.Try not to
pinch them when installing them.Use curil K2 good German goop.
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8650
Threads: 564
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on July 21st, 2004 at 09:46 PM |
|
|
Hi
I always used rubber grease on them as they are supposed to move in & out as the motor expands and I polished the bores that they slide in with
1200 wet & dry.
1302Steve
|
|
|
