| [ Total Views: 510 | Total Replies: 10 | Thread Id: 32375 ] |
|
|
 Dannyboy
Veteran Volks Folk
half man , half horse
Posts: 2306
Threads: 357
Registered: January 24th, 2004
Member Is Offline
Location: Randwick , Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: about 2" off the floor
|
| posted on November 30th, 2004 at 09:42 PM |
|
|
T3 extractor question
Have a question on t3 extractors. Once bolted to the motor and in the car how far does the extractor flange sit from the rear apron ( valance).
I'm getting a custom muffler made up and need a rough measurement.
cheers Dan
"If i had to explain you wouldnt understand"
The Lower Class
|
|
|
DallanMulley
A.k.a.: Dallan Mulley
Seriously Crusin Dubber
Posts: 145
Threads: 19
Registered: April 5th, 2004
Member Is Offline
Location: South Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: OLD
|
| posted on December 4th, 2004 at 12:28 PM |
|
|
Just gone and measured my 62 the flange is 30 mm but the silencer pipe comes out lower than the apron.
|
|
|
Dannyboy
Veteran Volks Folk
half man , half horse
Posts: 2306
Threads: 357
Registered: January 24th, 2004
Member Is Offline
Location: Randwick , Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: about 2" off the floor
|
| posted on December 4th, 2004 at 05:18 PM |
|
|
What car have you measured it from and roughly how much lower is it. Could you run a Stinger or would you need a cut out in the apron?
Cheers , thanks for being bothered!
Dan
"If i had to explain you wouldnt understand"
The Lower Class
|
|
|
frenzix
Son of Jim - Creator of Good
Posts: 2742
Threads: 195
Registered: December 8th, 2003
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 4th, 2004 at 07:20 PM |
|
|
on the 69square, my stinger fits fine.. clears the apron...
|
|
|
frenzix
Son of Jim - Creator of Good
Posts: 2742
Threads: 195
Registered: December 8th, 2003
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 4th, 2004 at 07:21 PM |
|
|
as long as you get a type3 stinger..
|
|
|
Dannyboy
Veteran Volks Folk
half man , half horse
Posts: 2306
Threads: 357
Registered: January 24th, 2004
Member Is Offline
Location: Randwick , Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: about 2" off the floor
|
| posted on December 4th, 2004 at 08:05 PM |
|
|
T3 stinger , Frenzix are you pulling my pud? Never heard or seen one.
Dan
"If i had to explain you wouldnt understand"
The Lower Class
|
|
|
frenzix
Son of Jim - Creator of Good
Posts: 2742
Threads: 195
Registered: December 8th, 2003
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 5th, 2004 at 03:39 PM |
|
|
teehee
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
frenzix
Son of Jim - Creator of Good
Posts: 2742
Threads: 195
Registered: December 8th, 2003
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 5th, 2004 at 03:40 PM |
|
|
any 3 bolt should do
|
|
|
Dannyboy
Veteran Volks Folk
half man , half horse
Posts: 2306
Threads: 357
Registered: January 24th, 2004
Member Is Offline
Location: Randwick , Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: about 2" off the floor
|
| posted on December 5th, 2004 at 04:37 PM |
|
|
LOL , bloody knew it!
Dan
"If i had to explain you wouldnt understand"
The Lower Class
|
|
|
shiftyvw
Wolfsburg Wizard
Posts: 523
Threads: 44
Registered: September 11th, 2002
Member Is Offline
Location: Seven Hills NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 5th, 2004 at 06:53 PM |
|
|
If your planning on using a stinger im assuming this is a hot motor. Where are you getting big headers from. I had to build my own 1 7/8 system when I
put the 2.3 with IDA's in the squareback. |
|
|
Dannyboy
Veteran Volks Folk
half man , half horse
Posts: 2306
Threads: 357
Registered: January 24th, 2004
Member Is Offline
Location: Randwick , Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: about 2" off the floor
|
| posted on December 5th, 2004 at 08:01 PM |
|
|
| Quote: | Originally
posted by shiftyvw
If your planning on using a stinger im assuming this is a hot motor. Where are you getting big headers from. I had to build my own 1 7/8 system when I
put the 2.3 with IDA's in the squareback.
|
LOL i wish!!! It's only a 1776 with 44's , nowt fancy . The headers are only 1 5/8 which will be okay for now i reckon.
Dan
"If i had to explain you wouldnt understand"
The Lower Class
|
|
|
