| [ Total Views: 744 | Total Replies: 7 | Thread Id: 34720 ] |
|
|
 *did*
A.k.a.: Steve
Posts: -16
Threads: 0
Registered: September 10th, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: happy 
|
| posted on January 27th, 2005 at 05:03 PM |
|
|
SOLD!! Hotwire mags: 6 and 7 inch wide BRAND NEW TYRES
Hi folks,
As always I am selling my hotwire mags.
The brand is performance australia, not cheviot.
They are 4 stud to suit later beetles, superbugs and probably type 3's.
Two 14x6 inch mags with 195/65R14 Tyres
Two 14x7 inch mags with 215/65R14 Tyres
No kerb rash, no scratches (except for one on the inner side of one rim where the tyre guys scratched it!), almost perfect!
The tyres are BRAND NEW Goodyear Regatta's that cost almost $400 in total. The 215's still have the 'hairs' on them and have not been driven. The
195's dont have the hairs on them anymore but are still 99%.
They also come with a full set of 16 near new chrome wheel bolts and washers. (retail: $8 per bolt!!)
If you are after a set of hotwires ready to bolt on with good tyres then these are for you.
$500 negotiable/swap for stuff maybe
Cheers, Steve
0422669966 or u2u
Blackburn 3130
[Edited on 8/5/05 by *did*]
[ Edited on 3/10/05 by *did* ] |
|
|
*did*
A.k.a.: Steve
Posts: -16
Threads: 0
Registered: September 10th, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on May 8th, 2005 at 06:26 PM |
|
|
bump!! |
|
|
oval TOFU
Son of Jim - Creator of Good
Bitte, ein Bit!
Posts: 2946
Threads: 234
Registered: July 10th, 2003
Member Is Offline
Location: Pt Cookie, Melburg
Theme: UltimaBB Pro Grey
Mood: :booM
|
| posted on May 10th, 2005 at 11:35 PM |
|
|
free bump
...and Robert's ya father's brother...
|
|
|
*did*
A.k.a.: Steve
Posts: -16
Threads: 0
Registered: September 10th, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on May 25th, 2005 at 11:23 AM |
|
|
thanks mate!
ooh another bump |
|
|
andytlr
Seriously Crusin Dubber
Posts: 109
Threads: 13
Registered: May 27th, 2005
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: Keen as mustard
|
| posted on May 28th, 2005 at 05:44 PM |
|
|
Because the stock wheels on a bettle are much thinner do you have to do anything when putting these on to make them fit? or do they just slide further
in? |
|
|
*did*
A.k.a.: Steve
Posts: -16
Threads: 0
Registered: September 10th, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on May 30th, 2005 at 10:19 AM |
|
|
7 inch rears: if you have a early rear axles (shorter) on your bug then they will apparently fit without wide rear guards, other than that you need
wider guards.
6 inch fronts: stick out a little bit past the guards, about 1-2cm
i think the 6 inch ones dont stick out if you put them on the back
but then you have to chase down another pair of 6's for the front  |
|
|
*did*
A.k.a.: Steve
Posts: -16
Threads: 0
Registered: September 10th, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on May 30th, 2005 at 10:20 AM |
|
|
ps: they dont rub on the body |
|
|
*did*
A.k.a.: Steve
Posts: -16
Threads: 0
Registered: September 10th, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: happy
|
| posted on September 21st, 2005 at 04:56 PM |
|
|
wow, bump |
|
|
