| [ Total Views: 603 | Total Replies: 3 | Thread Id: 4035 ] |
|
|
 sand kombi
Officially Full-On Dubber
Posts: 345
Threads: 71
Registered: February 14th, 2003
Member Is Offline
Location: Logan Village[out skirts of Brisbane]
Theme: UltimaBB Pro Blue ( Default )
|
 posted on February 27th, 2003 at 12:30 PM |
|
|
dellorto's carbies
Will 40mm Dellorto's off a alfa romeo fit a 2ltr motor
what else will I need to make them work ,eg. manifold, linkages etc.it is 2nd hand and unseen as yet |
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 27th, 2003 at 12:46 PM |
|
|
A 2L T4?
you will need T4 manifolds (same as IDF 36,40,44)
Air cleaners
Linkage.
Gaskets
Maybe vents
Definetely jets
They need to be restudded. The Alfa only has 2 studs for the air cleaner so you will need the extra ones put in.
They also have a choke mechanism the needs disconnecting if going on an upright motor cause it interferes with the shroud.
You sure the are DRLA 40's - just unusual
Mostly DRLA 36's or IDF's- still should be ok though
Futue te ipsum!!!
|
|
|
sand kombi
Officially Full-On Dubber
Posts: 345
Threads: 71
Registered: February 14th, 2003
Member Is Offline
Location: Logan Village[out skirts of Brisbane]
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 27th, 2003 at 11:05 PM |
|
|
thanks heaps for the info. still seems to need a lot to get them going but getting bits slowly it should be to bad
As to the 40mm size thatis just what the ad said,what is the 40mm/36mm ,just the throught width or something else,and is it marked
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
sand kombi
Officially Full-On Dubber
Posts: 345
Threads: 71
Registered: February 14th, 2003
Member Is Offline
Location: Logan Village[out skirts of Brisbane]
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 27th, 2003 at 11:08 PM |
|
|
other side
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 28th, 2003 at 11:14 AM |
|
|
Have you bought these?
Something dont seem right. Are you sure they are not DHLA's ie side draft?
The carbs i have seen have a flat top not a flange at both ends.
Sorry .... it is hard trying to visualise at the office.
The red stuff dont look familiar either
Futue te ipsum!!!
|
|
|
sand kombi
Officially Full-On Dubber
Posts: 345
Threads: 71
Registered: February 14th, 2003
Member Is Offline
Location: Logan Village[out skirts of Brisbane]
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 28th, 2003 at 01:04 PM |
|
|
I dont know they are on ebay, thought a few people would know alot more about them as I don't know what to look for |
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 28th, 2003 at 02:09 PM |
|
|
They don't look like the 40mm dells I run. Blue mite be rite, sure they are side draught? |
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 28th, 2003 at 03:04 PM |
|
|
Pass on em mate.
You can do better here in Australia.
Give Alfabits a call and see what they have
What state are you in?
Futue te ipsum!!!
|
|
|
