| [ Total Views: 642 | Total Replies: 5 | Thread Id: 47521 ] |
|
|
 RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 3rd, 2006 at 05:12 PM |
|
|
Kadron Problems
I am having problems with my kadron carburettors or one of them to be precise.I have recently had them cleaned as the car was sitting for a while and
there was a bit of varnish build up the carb guy also replaced both float valves and one float.I put them in the car adjusted the idle and they ran
fine for a couple of weeks. Last week i was driving and the bus started to hesitate running on three and then two cylinders. The right side carb was
flowing way too much fuel the plugs had oiled and ceased to fire. float valve is free and seems to operate ok dropped in a new set of plugs and it ran
for about a km before they stopped firing again idle adjust screw has no effect. I am running an electric fuel pump that I have run for years without
problems. Any ideas?
|
|
|
shiftyvw
Wolfsburg Wizard
Posts: 523
Threads: 44
Registered: September 11th, 2002
Member Is Offline
Location: Seven Hills NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 3rd, 2006 at 05:48 PM |
|
|
if you have an electric fuel pump, switch the ignition on so the pump is running but the engine isnt, and have a look down both carbs to see if the
side your having problems with is drizzling fuel into the engine, if it is replace the needle and seat.
testing 1 2 3...
|
|
|
RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 3rd, 2006 at 07:13 PM |
|
|
Needle and seat is the float valve or something else? Iturned on the fuel pump and it started to trickle, kept going after I had turned it off. I
hadnt noticed this before as its in a bus and you cant get your head in there had to use a mirror and a light, the float valve is notstuck but I was
thinking maybe an extra washer or two might help it get a more positive shut off?
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 3rd, 2006 at 08:14 PM |
|
|
Sounds like needle and seat (float valve)
Try reading hear - AJ Simms site. Lots of Kadron help here
http://www.lowbugget.com/
Futue te ipsum!!!
|
|
|
jakjones
Officially Full-On Dubber
Posts: 217
Threads: 3
Registered: March 9th, 2004
Member Is Offline
Location: central coast
Theme: UltimaBB Pro Blue ( Default )
Mood: Settled
|
| posted on January 3rd, 2006 at 09:52 PM |
|
|
maybe the needle valve has come loose ?
or is internally blocked , replace it again.
|
|
|
RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 7th, 2006 at 09:24 PM |
|
|
Thanks guys found the problem my new float was a sink.
|
|
|
