| [ Total Views: 572 | Total Replies: 1 | Thread Id: 6350 ] |
|
|
 rozrob
Slammed & Awesome Dubber
Posts: 85
Threads: 18
Registered: January 8th, 2003
Member Is Offline
Location: weed heads
Theme: UltimaBB Pro Blue ( Default )
Mood: lovin life
|
| posted on May 13th, 2003 at 04:02 PM |
|
|
stabaliser bar
while changing the shocks on my '74 kombi just noticed the stabaliser bar was snaped at the left hand clamp. just wondering how important is it?
where can i find a replacement in the gold coast area and are they expensive? cheers scotte
|
|
|
Andy
Son of Jim - Creator of Good
Andy's Adventures
Posts: 2818
Threads: 181
Registered: November 5th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy Man
|
| posted on May 13th, 2003 at 10:19 PM |
|
|
Never had to replace one, so not sure what's involved in replacing???
Most wreckers in Brissy will have one on a parts bus (Micks Motors, Action Auto, Harding European etc).
As for whether it's needed, it will stop the bus leaning too much in corners. Could be dangerous if you try going through a corner too fast, or
with a lot of high weight (roof rack etc).
Good luck,
Andy
|
|
|
rozrob
Slammed & Awesome Dubber
Posts: 85
Threads: 18
Registered: January 8th, 2003
Member Is Offline
Location: weed heads
Theme: UltimaBB Pro Blue ( Default )
Mood: lovin life
|
| posted on May 15th, 2003 at 11:50 AM |
|
|
cheers keep you all posted on our travels
|
|
|
Baja Wes
Bishop of Volkswagenism
V6 Baja Pioneer
Posts: 3119
Threads: 94
Registered: August 26th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Content
|
| posted on May 15th, 2003 at 12:21 PM |
|
|
you'll just get more body roll without it.
I don't have any stabiliser bars on my Baja. They reduce suspension travel (articulation anyway) offroad so it is best to remove them on an
offroad car. It just means you get body roll like a land rover  (not
that bad actually)
Brad might have one floating around, he has wreck a few kombi's in his time. email him at brad@offroadvw.net . He's nowhere near the gold
coast area though 
[Edited on 15-5-2003 by Baja Wes]
|
|
|
Purple Martin
A.k.a.: Martin
Fahrvergnugen
Posts: 913
Threads: 141
Registered: February 13th, 2003
Member Is Offline
Location: Canberra
Theme: UltimaBB Pro Blue ( Default )
Mood: warm & fuzzy
|
| posted on May 15th, 2003 at 02:19 PM |
|
|
I replaced mine a couple of months ago (it had snapped in the same place as yours - apparently it's quite common).
I picked up a second hand one from my local VW mechanic with the rubber blocks still on it - they'd be a pain to take off and put back on.
Taking out the old one and fitting the new one was quite easy, from memory it goes like this:
On each side you remove the bolt, and then you have to get the clip off the bottom of the metal clamp that goes around the rubber block. You get the
clip off by straightening the end of it out by hitting it with a big hammer and a blunt cold chisel (it's easier to swing the hammer if the bus
is up on ramps). Make sure you're straightening the correct end of the clip, it's tapered so when you slide it off the clamp you'll
need the wide end straightened. Use the hammer to help slide the clip off.
Now you use the cold chisel (or a very big screwdriver) to force the clamp apart so it's not gripping the rubber block.
Once you've got the clamps loose on both sides you can take tho broken bar out with the rubber blocks still on it.
Then stick the new bar in, force the clamps back together, slide the clips back on (use the hammer), bend the ends of the clips so they won't
work loose (use the hammer) and put the bolts back.
1959 red & white Beetle
1975 Kombi camper
|
|
|
