| [ Total Views: 1810 | Total Replies: 4 | Thread Id: 66840 ] |
|
|
 rob53
Officially Full-On Dubber
Posts: 385
Threads: 62
Registered: January 19th, 2007
Member Is Offline
Location: Campbelltown
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 5th, 2008 at 10:31 AM |
|
|
Carpet Glue
What is the type of glue you use to attach the carpets? And where's a good source to get it?
Thanks,
Rob
Thats not rust, it's ah ... orange primer ... yep that's what it is ...
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on January 5th, 2008 at 10:39 AM |
|
|
local hardware shop and get some spray on contact adhesive
make sure you remove all the old glue n dirt before re glueing the carpets in place
test fit them beore glue as well
|
|
|
 65busser
Super Moderator
Posts: 1795
Threads: 224
Registered: November 6th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: dakked
|
| posted on January 6th, 2008 at 10:33 AM |
|
|
TAC Adhesives do a good one, but you might have to buy it from a trimmer. It's called 205 Brush Contact. Otherwise Bunnings have a good spray
adhesive by Fuller called Spray Bond Permanent. It says it's for light weight materials but is strong enough for carpet. Most canned spray adhesives
aren't strong enough but Fuller will do it.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on January 7th, 2008 at 09:38 AM |
|
|
I just used contact cement... in tubes...
I coated the body with contact..
then pushed the carpet where it needed to go
so there will be contact on both sides
and took the carpet off for the contact to become tacky
then pressed it into position... You only get one chance doing it this way as the contact sticks on contact...
and when it sticks... it sticks...
the other way is to coat the body with contact - from a tube... [large tubes from GO LO]
and push the carpet into its location... You can move the carpet into place as the contact hasn't dried...
and leave it there....
just press all over after about 15 minutes...
and it should stick....
this is not the recommended way to apply Contact Cement... and it may come off...
You then apply more contact and let it go tacky before reapplying... and it shouldn't come off...
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
rob53
Officially Full-On Dubber
Posts: 385
Threads: 62
Registered: January 19th, 2007
Member Is Offline
Location: Campbelltown
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 7th, 2008 at 10:49 AM |
|
|
Thanks for the help everyone. I give the fuller spray adhesive a go.
-Rob
Thats not rust, it's ah ... orange primer ... yep that's what it is ...
|
|
|
