| [ Total Views: 500 | Total Replies: 5 | Thread Id: 7584 ] |
|
|
 greenbuggy
Learner Dubber
Posts: 2
Threads: 1
Registered: June 15th, 2003
Member Is Offline
Location: Hawthorn, VIC
Theme: UltimaBB Pro Blue ( Default )
|
 posted on June 18th, 2003 at 01:27 AM |
|
|
Valve cover gasket and oil change nuts leaks
I am a computer tech that is new to vw engine, so pardon my ignorance.
My green buggy has always leaking oil since I adjusted the valve myself. I suspect that the valve cover gasket is leaking. What do you guys use to
glue the gasket to the cover? Do you guys put something else between the gasket and the engine block?
I am thinking of "super gluing" the gasket to the cover and see if it still leak. Please advise me if I should do otherwise.
And for the oil sump big bolt and the 6 maller bolt they also leak and I was thinking maybe I should use torque wrench and follow the spec. Should I
use some sort of sealant? What do you guys use?
Thanks for your help guys,
Greenbuggy |
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on June 18th, 2003 at 07:10 AM |
|
|
Did you use new gaskets ??
For the valve cover, are they flat n not bent?? only use a small amount of gasket goo to stick the gasket to the valve cover, dont use any on the
cylinder head.
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2003 at 08:20 AM |
|
|
Make sure the head and valve cover are in good condition.
I just "lube" the cork gasket with bearing grease. Just make sure it fits snug.
Replace gaskets each time. Dont reuse them.
As for the sump plate - same thing. Lube the paper gaskets with grease. New gaskets each time. Make sure the copper washers are there, they come in
the gasket kit.
Also make sure the sump plate is flat. If not either get a new one or dimple the holes carefully away from the block.
Unlikley you will get it bone dry but it certainly shouldnt drip or leave annoying marks
Futue te ipsum!!!
|
|
|
geodon
Wolfsburg Wizard
Posts: 478
Threads: 63
Registered: August 28th, 2002
Member Is Offline
Location: geelong
Theme: UltimaBB Pro Blue ( Default )
Mood: stumbling
|
| posted on June 18th, 2003 at 08:49 AM |
|
|
The rocker cover gaskets that have leaked for me have been due to the top of the gasket falling as I have put the rocker cover on. Do what Dave has
suggested & goo them on the rocker cover. I also gently tap them upwards once they are on because the action of the clip going on can lever them
downwards.
The oil strainer nuts should be domed with copper washers to stop oil leaking down the threads.
|
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2003 at 09:12 AM |
|
|
I had major leaks with my tappets cover's when i first got my car. I found that at the bottom the gasket would bend up and a gp would form also,
try another gasket. make sue ur using the cork ones, the rubbers ones are $%#^. |
|
|
greenbuggy
Learner Dubber
Posts: 2
Threads: 1
Registered: June 15th, 2003
Member Is Offline
Location: Hawthorn, VIC
Theme: UltimaBB Pro Blue ( Default )
|
 posted on June 18th, 2003 at 09:48 AM |
|
|
Thanks guys for the fast reply.
Some more information that I should mention, I always use new gaskets and I only put some whell bearing grease on the gaskets that goes to the
cylinder head and glue on the side that goes to the valve cover.
I will check if the valve cover gaskets was actually shifted when i put the valve cover to the cylinder head.
For the oil plug, I did use the new copper washers but the oil still drip, and I can see that it drip from all 6 nuts and the big center nut. I was
thinking maybe I did not thighten it enough, it there any side effect if I over tighten it?
Cheers,
SAM |
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2003 at 10:04 AM |
|
|
The side effect is stripping the case thread. Just "nip" them. No real force should be needed.
Maybe a new plate is in order
Futue te ipsum!!!
|
|
|
Purple Martin
A.k.a.: Martin
Fahrvergnugen
Posts: 913
Threads: 141
Registered: February 13th, 2003
Member Is Offline
Location: Canberra
Theme: UltimaBB Pro Blue ( Default )
Mood: warm & fuzzy
|
| posted on June 18th, 2003 at 11:28 AM |
|
|
i read a really long post about lubrication on here 2 days ago that said that overtightening the sump plate nuts can bend the sump plate, resulting in
permanent leaks. It said always use fresh gaskets, and always use a torque wrench to tighten nuts to exactly the right settings - but it sounds like
in your case the damage may already be done.
1959 red & white Beetle
1975 Kombi camper
|
|
|
geodon
Wolfsburg Wizard
Posts: 478
Threads: 63
Registered: August 28th, 2002
Member Is Offline
Location: geelong
Theme: UltimaBB Pro Blue ( Default )
Mood: stumbling
|
| posted on June 18th, 2003 at 02:41 PM |
|
|
No domed nuts???
It looks like the oil is running down the threads. Try some Loctite on the threads.
Also, you may well have a warped base plate. You could try 2-3 extra gaskets (they are dirt cheap) & you might get lucky!
[Edited on 18-6-2003 by geodon]
|
|
|
