[ Total Views: 638 | Total Replies: 4 | Thread Id: 78146 ] |
|
crsedge
Wolfsburg Wizard
Posts: 687
Threads: 84
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: Cheery
|
posted on August 2nd, 2009 at 09:11 PM |
|
|
15x 7" Fuchs on the rear of '54 oval
Hi All,
I am wanting to put a set of 15x 6" Fuchs on the front of a standard '54 Oval Beetle, and 15x 7" on the back.
I am keen to avoid a narrowed beam on the front, and think the 6" will sneak in. I have a set of adaptor plates to accept the fuchs, but that too
will increase the width of track. Has anyone tried the same, did it work, and if not, what did you have to do?
Equally, I am wanting to put a set of 7" on the back. It does have a 1500 gearbox, which I believe may widen the track. Has anyone put 7" on the
back of an oval, if so was there anything dramatic that had to be done?
Thanks all.
Cheers
Craig
May '55 Oval
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
posted on August 2nd, 2009 at 10:39 PM |
|
|
yep they fit fine
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
posted on August 2nd, 2009 at 11:57 PM |
|
|
Hi
Adaptors are illegal in NSW for good reasons, not sure where you are.
Why not get some Vintage Vee Dub front discs in Porsche pattern and some rear drums with Porsche pattern as well.
I ran 6 & 7 inch Cookies on a 73 1300 bug and they fitted fine, fitting the discs and rear drums and you should end up about the same.
Steve
|
|
modulus
A.k.a.: Peter Hill
Veteran Volks Folk
Posts: 2009
Threads: 76
Registered: July 1st, 2003
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro White
Mood: modular
|
posted on August 3rd, 2009 at 11:27 AM |
|
|
Adaptors are also illegal in Victoria.
Vehicle Standards Information Bulletin 8 (Modification Guide) also states "The stud pattern of the replacement wheel must be the same as the
original." which, on the surface of it, would also appear to rule out Porsche wheels.
hth
|
|
crsedge
Wolfsburg Wizard
Posts: 687
Threads: 84
Registered: January 4th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: Cheery
|
posted on August 3rd, 2009 at 02:17 PM |
|
|
The car currently runs drums all around, and I am wanting to avoid the expense of doing a disc conversion.
The stud pattern will remain 5 stud, so technically that is the same stud pattern (just different PCD!)... well it is in my book!
So, will they fit with adaptor plates, or will the drum need to be re-drilled due to the added width of adaptor plates?(with the threads protruding
rather than holes drilled into the drum)
Cheers
Craig
(Melb)
May '55 Oval
|
|