| [ Total Views: 1103 | Total Replies: 10 | Thread Id: 81241 ] |
|
|
 1600
Learner Dubber
Posts: 9
Threads: 3
Registered: November 16th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 7th, 2010 at 09:38 PM |
|
|
webers
Hey all you type 3 'thusiasts, and lovers of lesser aircooleds, (just kidding I love them all). Was hoping someone could share some weber knowledge
with me. Am looking at the CB Performance IDF kit for type 3, that comes with everything except carbs. I believe the 36 IDF's from Alfasuds and
Sprints will fit these manifolds. Anybody done this? Love the Forum, cheers.
|
|
|
Peter_D_C
Seriously Crusin Dubber
Posts: 102
Threads: 20
Registered: June 18th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 12th, 2010 at 09:50 PM |
|
|
I have the exact set up you mentioned. Fire away with any q's.
Fits fine with plenty of room under the decklid.
The air filters are a bit restrictive, so am putting on some ramflow's when the second one finally turns up (the shop, naturally, only had one when i
went).
1969 Type 3 Squareback
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 12th, 2010 at 10:10 PM |
|
|
There is a set of DRLA Dellortos for sale here for a type 3
Get those 
here ya go
http://forums.aussieveedubbers.com/viewtopic.php?tid=81300&page=1#pid756805
Futue te ipsum!!!
|
|
|
64vwmark
A.k.a.: Mark Shepherd
Fahrvergnugen
Posts: 930
Threads: 82
Registered: December 6th, 2004
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Black
|
| posted on January 12th, 2010 at 10:59 PM |
|
|
I have 36 IDF's on the 1641 in my buggy. They work gret on a 1600 once you richen them up a bit. The air bleeds on the idle circuit are a little big
(2mm). I soldered mine up and redrilled them at 1.5mm. That made a massive improvement. I also swapped from 47 idle jets up to 50's which helped a
lot also.
Beach Buggy
74 L Beetle
Mk4 Golf |
|
|
Peter_D_C
Seriously Crusin Dubber
Posts: 102
Threads: 20
Registered: June 18th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 13th, 2010 at 09:52 AM |
|
|
Hi Mark,
How much of an improvement was soldering / re-drilling the air bleeds?
Ive got a mild 1915 and am running 60 idles. 32 vents also. From memory reading somewhere the 36's require larger than usual idles to counter the
air bleed size?(i could be wrong). Is that what you found?
1969 Type 3 Squareback
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 13th, 2010 at 11:32 AM |
|
|
When i was running 36's i found the small idles worked best ( but blocked VERY easily)
1.25 x the body size seems to be the formulae
see here
http://www.aircooled.net/gnrlsite/resource/articles/jetting.htm
There is a link called http://www.carburetorclinic.com/36_idf.htm
that is all about rebuilding IDF36s that is VERY good but the link doesnt seem to be working for me
Barry
Futue te ipsum!!!
|
|
|
Peter_D_C
Seriously Crusin Dubber
Posts: 102
Threads: 20
Registered: June 18th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 13th, 2010 at 12:15 PM |
|
|
Found it:
http://www.thesamba.com/vw/forum/viewtopic.php?t=315815&highlight=idf+jet...
Harney is the man WRT webers.
1969 Type 3 Squareback
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 13th, 2010 at 05:12 PM |
|
|
mmm....thats the guy but that is excerpts from the article he wrote
Dunno if i agree with the jetting
Mine was banging BIG TIME with 50's in there
I was using F11
No way could i get the F57's to work
In the end i was
32 vents
F11
45 idles
135 mains
180 or 200 airs
Ran OK - would like to go back and try again with IDF 36s
Personally - when i had Webers i though Weber Dells, they are all the same
I now have DRLA40's
Chalk and cheese
Give me Dellortos any time
Futue te ipsum!!!
|
|
|
64vwmark
A.k.a.: Mark Shepherd
Fahrvergnugen
Posts: 930
Threads: 82
Registered: December 6th, 2004
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Black
|
| posted on January 13th, 2010 at 06:33 PM |
|
|
| Quote: | Originally
posted by Peter_D_C
Hi Mark,
How much of an improvement was soldering / re-drilling the air bleeds?
Ive got a mild 1915 and am running 60 idles. 32 vents also. From memory reading somewhere the 36's require larger than usual idles to counter the
air bleed size?(i could be wrong). Is that what you found?
|
The improvement with soldering / redrilling the air bleeds is very noticeable. Not only does it richen them up but it removes a big flat spot on
acceleration.
Beach Buggy
74 L Beetle
Mk4 Golf
|
|
|
1600
Learner Dubber
Posts: 9
Threads: 3
Registered: November 16th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 16th, 2010 at 09:30 PM |
|
|
Thanks all for your replies and info. Thanks for the link Bizarre, will go with the ida's as they were very cheap. Peter_D_C and 64vwmark, might
check in with any q's when I am closer to doing the job if thats ok. Am planning in advance, I don't even have the car yet, gotta pick it up from
interstate. Getting a bit excited. Cheers.
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 29th, 2010 at 08:35 PM |
|
|
for other that may be interested here is the post less pictures
http://web.archive.org/web/20080117102107/www.carburetorclinic.com/36_idf.htm
Futue te ipsum!!!
|
|
|
