| [ Total Views: 576 | Total Replies: 7 | Thread Id: 83683 ] |
|
|
 57 oval
Seriously Crusin Dubber
Oval type 4 Fuel Injected
Posts: 184
Threads: 48
Registered: February 5th, 2008
Member Is Offline
Location: Whyalla
Theme: UltimaBB Pro Grey
Mood: Oval
|
| posted on May 16th, 2010 at 08:14 AM |
|
|
O ring and seals question
Just bought a gasket overhaul kit for a 1600 T/P and although I know that they supply gaskets and seals for most engine sizes in the kit, what is the
about 50mm O ring for ? also there are six thick O rings about 13mm dia.
there is a seal / oring type about 25mm and while I am in asking mode two black rubbers about 10mm high about 10 mm outside with about an 8mm bore and
four browny colour 12mm outside dia 8 mm bore and about 8 mm high.
I have fitted a new set of barrels and pistons and new heads to my twin port but havent seen these items any were in my travels, also about to do the
rear main seal, do 1600 T/P have a oring in the inside bore of the flywheel? any help appreciated
Cheers
RJ
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 16th, 2010 at 05:47 PM |
|
|
what is the about 50mm O ring for ? also there are six thick O rings about 13mm dia.
the 50mm goes in the flywheel
the 13mm are for the 6 crancase center bolts
|
|
|
57 oval
Seriously Crusin Dubber
Oval type 4 Fuel Injected
Posts: 184
Threads: 48
Registered: February 5th, 2008
Member Is Offline
Location: Whyalla
Theme: UltimaBB Pro Grey
Mood: Oval
|
| posted on May 16th, 2010 at 05:59 PM |
|
|
Found were this one goes
"seal / oring type about 25mm "
on the distributor shaft were it fits into tthe block
Found were the 50 mm goes thanks
six o rings not needed as I didnt split the case
Thanks for the reply thou
Just got to find a home for these
"two black rubbers about 10mm high about 10 mm outside with about an 8mm bore and four browny colour 12mm outside dia 8 mm bore and about 8 mm
high".
All of these looik like a small piece of tube
Cheers
RJ
|
|
|
pod
A.k.a.: paul mrvw061
Compulsive Aussie Vee Dubber
i`ve got to finish this thing one day
Posts: 4980
Threads: 145
Registered: December 28th, 2003
Member Is Offline
Location: campbelltown,nsw
Theme: UltimaBB Pro Yellow
Mood: could be better
|
| posted on May 16th, 2010 at 06:31 PM |
|
|
sounds like the oil cooler seals
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 16th, 2010 at 06:39 PM |
|
|
yep cooler seals
|
|
|
57 oval
Seriously Crusin Dubber
Oval type 4 Fuel Injected
Posts: 184
Threads: 48
Registered: February 5th, 2008
Member Is Offline
Location: Whyalla
Theme: UltimaBB Pro Grey
Mood: Oval
|
| posted on May 16th, 2010 at 07:11 PM |
|
|
Nop not them, the set had two different types of oil cooler seals, used them, still the mistery seals
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2671
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on May 16th, 2010 at 07:41 PM |
|
|
Browny colour or white (depending on supplier of engine set)may be the rocker shaft seals for the 40hp
|
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on May 17th, 2010 at 10:59 AM |
|
|
some sets supply both types of seals
so depeneding on which engine you have
depends on which seals are used
|
|
|
