| [ Total Views: 809 | Total Replies: 5 | Thread Id: 87318 ] |
|
|
 Fastback
Learner Dubber
Posts: 4
Threads: 1
Registered: November 25th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 25th, 2010 at 10:43 AM |
|
|
T3 oxyboxer problem
Hi there
I am new to the Forum
I currently own a scruffy T3 Fastback which has been off the road for some time
I had the engine rebuilt some time ago due to contaminated fuel and detonation however there is still a problem with it; the pushrods keep moving
(jumping)out of the rocker seats.
Initially I thought it was not enough movement/clearance in the new heads but now I am beginning to suspect it may be the new dual stronger springs
and incorrect adjustment causing binding/jamming.
Any thoughts on this would be appreciated as I am clearing out the garage to start working on it.
Brief engine specs are
DH wasserboxer block
94x82 piston and cylinder assy
CB 044 Supermag Plus heads with dual super rev springs (ported and polished)
Dual twin throat dellorto 45D carbys |
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
| posted on November 25th, 2010 at 10:55 AM |
|
|
have you checked the rocker geometry out
Push rod angle to rocker screw at lift etc
|
|
|
Fastback
Learner Dubber
Posts: 4
Threads: 1
Registered: November 25th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 25th, 2010 at 11:21 AM |
|
|
Hi Hellbugged
Still clearing space to work on it. Was originally rebuilt by small aviation firm but the mechanic was badly injured and the firm closed before the
problem could be fixed so its up to me now and I have done little work on aircooled motors. Will check it out when its on the bench.
BTW the car was originally built by Hellbug  |
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
| posted on November 25th, 2010 at 01:07 PM |
|
|
ha ha, yes the oxy boxer a bit of a ive away there
Not the grey "hellfasty"?
They didnt happen to reduce compression with the rebuild by any chance?
pics if you can
Always the best help for remote diagnosis
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on November 25th, 2010 at 01:36 PM |
|
|
I think i went for a run in that type 3.....
I'd check for clearance before coil bind on those springs too. Some major issues to be sorted to have the pushrods coming out of the rocker. Firstly
I'd look at spring tension. but you say they are new so if the springs were tested and installed to the correct installed height, they should be ok,
so next would be the valve lift is more than the spring can handle, should aim for .100" clearance before bind.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Fastback
Learner Dubber
Posts: 4
Threads: 1
Registered: November 25th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 25th, 2010 at 03:28 PM |
|
|
Thanks for the quick replies and what to check for.
The car is orange, it was originally built for someone in Bondi beach. He unfortunately died and his brother took it over I bought it from him and had
it shipped to WA.
Have posted a few pics but will not be able to get some good engine pics for a week or so, am getting rid of T1 etc parts at the moment as the garage
is full of stuff.
Th car does not look as pretty as in the pic
Edit: Compression ratio 8.5 to 1 from memory
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
