| [ Total Views: 897 | Total Replies: 25 | Thread Id: 88385 ] |
|
|
 bikecrazy
Casual Dubber
Posts: 24
Threads: 13
Registered: September 28th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2011 at 08:13 PM |
|
|
beetle rear hub nuts
any extra ideas on howto remove the rear hub nuts tried bar tried rattle gun etc
|
|
|
 barls
A.k.a.: Mr indestructible
Super Administrator
Causer of Chaos and Mayhem
Posts: 9470
Threads: 296
Registered: June 22nd, 2004
Member Is Offline
Location: cruising in denistone east
Theme: UltimaBB Streamlined2
Mood: indestructible? and listening to the voices
|
| posted on January 27th, 2011 at 08:14 PM |
|
|
wd40 then soak.
after that breaker bar with bit of pipe on it.
oxy and heat the nut.
|
|
|
bikecrazy
Casual Dubber
Posts: 24
Threads: 13
Registered: September 28th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2011 at 08:21 PM |
|
|
have been spraying with crc daily next step iguess will be oxy will that damage the shafts though or will it be fine if the heat is concentrated on
the nut
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2011 at 08:24 PM |
|
|
Settle down there barls! You shouldn't need to be doing any kind of heating and quenching work, unless they haven't been loosened since the 1970s.
WD40 is definitely a good start though. When they're really stuck, I use a long breaker bar, with wheel chocks (lengths of timber sleeper) either
side of the wheel. Leave the handbrake off and the car out of gear. Knock the split pin out and fit your socket firmly. Then, I rock the car backwards
and forwards against the wheel chocks using the breaker bar on the axle nut. When the car is rolling down off the side of the chock I pull upwards on
the bar with full force against the wheel's direction of travel. This may need to be repeated several times but usually gets the job done. In between
if it's really stuck and I get tired then I will give it a few blasts with the rattle gun.
|
|
|
bikecrazy
Casual Dubber
Posts: 24
Threads: 13
Registered: September 28th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2011 at 08:30 PM |
|
|
hey waveman as ive said tried rattle gun tried bar id say its time for heat
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2011 at 08:33 PM |
|
|
How long is your bar though? Go bigger and longer, I say. A good metre or more of extension bar will beat a rattle gun any day in my experience.
|
|
|
barls
A.k.a.: Mr indestructible
Super Administrator
Causer of Chaos and Mayhem
Posts: 9470
Threads: 296
Registered: June 22nd, 2004
Member Is Offline
Location: cruising in denistone east
Theme: UltimaBB Streamlined2
Mood: indestructible? and listening to the voices
|
| posted on January 27th, 2011 at 08:39 PM |
|
|
oxy on the nut is a last ditch effort mate,
just be happy i didnt just post this one as per the gun busters way
but seriously most loosen well before the use of an oxy.
|
|
|
Aussie Dubbin
Fahrvergnugen
Posts: 895
Threads: 90
Registered: July 21st, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2011 at 10:00 PM |
|
|
yeah its all about tools and technique. Get a solid (no flex) breaker bar about 1.5m away from the nut. Use a strong RHS in betwen the wheel nuts on a
diagonal to the ground with the wheel removed. This way as you rotate ere is no movement and all the force is applied to the nut. Once i couldn't do
it because i had not bout a big enough socket and i had to go to the local vw place. He got me to sit in the car ouof gear with my foot firmly on the
pedal and he put the breaker bar on near horozontal and gave a smalljump on the breaker and crack the tension was overcome. 36mm and 3/4" drive no
adaptors
|
|
|
helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on January 27th, 2011 at 10:08 PM |
|
|
Average adult weight on a 1.8m extension will remove the nut unless there is a problem. Then heat.
|
|
|
Birdman
Wolfsburg Wizard
Posts: 428
Threads: 49
Registered: May 19th, 2010
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 28th, 2011 at 07:27 AM |
|
|
Or just find a torquemeister which will get if off no problem. I donated mine to club VW sydney.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on January 28th, 2011 at 09:05 AM |
|
|
x2 for heat.
I've had to get the hot axe on some of mine, especially if the thread is abit ordinary.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on January 28th, 2011 at 05:00 PM |
|
|
Go to any tool shop of good repute and purchase a flogging spanner, no need to heat it, just a couple of hits with a 4LB lump hammer.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on January 28th, 2011 at 08:13 PM |
|
|
You can flog 7 shades of shit out of it with the BFH you can find, but it the threads are abit manky there's a good chance you can ruin the axles.
Ask me how I know
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on January 29th, 2011 at 10:11 AM |
|
|
Looks like they were over torqued to begin with.
|
|
|
annosL
Officially Full-On Dubber
Posts: 378
Threads: 43
Registered: December 28th, 2008
Member Is Offline
Location: albany
Theme: UltimaBB Pro Blue ( Default )
Mood: need to win lotto
|
| posted on January 30th, 2011 at 01:21 AM |
|
|
just replaced a wheel cylinder on my '60 beetle, nut would NOT move. Ended up using large jemmy bar wedged between two wheel bolts and floor then a
3/4 drive 36mm socket with tee-bar and on that two metres of 50mm waterpipe, could not move it by hand so stopped for a cuppa then in disgust hung
from a shed rafter and bounced on the pipe and FINALLY it moved! I thought the car would fall off the stands! Now I have to do the other side so
hopefully it will move too, my next shot would have been heat. In an earlier life working in a mine I watched a skilled fitter carefully remove a
large nut off a warman pump faceplate mounting bolt using a gas-axe with zero damage to the male thread but I wouldn't attempt that on an axle!
|
|
|
Uber Kafer
Wolfsburg Wizard
Posts: 414
Threads: 50
Registered: November 12th, 2009
Member Is Offline
Location: Bunbury (BunVegas) WA
Theme: UltimaBB Pro Blue ( Default )
Mood: Need a bigger shed..
|
| posted on January 31st, 2011 at 10:24 PM |
|
|
when I was 18 (and thats a long time ago) and before the days of the internet and specialised tool shopping at your fingertips I bought a 3/8" drive
socket to suit the wheel hub nut and got a 150 mm length of massive flat bar steel welded to it as a flogging tag. With the wheel still on the hub,
and with the tyre on the ground, I put the tool on the nut and whack the tag downwards with a gympie hammer (mallet) to break the bond. Sometimes I
have to hold the tool on the nut with my (steel capped) boot otherwise it slips slightly and burrs the nut.
Having a crappy old wheel and tyre on the hub helps to absorb any impact down through the tyre, and not through the bearing etc.
Works for me....
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on February 1st, 2011 at 06:27 AM |
|
|
Its the best way to break the initial resistance ,breaker bars and lumps of pipe flex's to much and a lot of time you cannot generate enough torque
to break the nut, with the flogging spanner it looses nothing in the translation, we use them at work all the time to loosen nuts that nut runner's
and rattle guns do not look at even 1" drive one's.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on February 1st, 2011 at 08:11 AM |
|
|
Flogging spanners are great maybe for crappy mining equipment that you don't own or as a last resort when your miles from anywhere but I certainly
don't recommend thier use in this aplication. Maybe for a course military thread like Whitworth which was specifically designed for rough handling
etc but IMO not to be used on the fine thread and hard axle of a VW rear hub nut. I've undone more of these than I need to remember, my 5' heavy
wall pipe and 3/4 socket ALWAYS come through. (maybe the one above in Joels may have required some heat  but age, over tension and corosion eventually have some effect)
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on February 1st, 2011 at 11:59 AM |
|
|
Both sides of my bug did that, I suspect the VW garage that the lady I bought it from used to get work done at would have probably over torqued them
with the rattle gun, then years of driving on dirt roads had it's effect.
But aside from that bolting my angle iron to the drum and using my 3/4 sydchrome socket and breaker bar always gets them undone.
Sometimes it takes leaving the wheel on and someone stepping on the brakes and all my weight on the bar but it gets it done
|
|
|
rocknrob
A.k.a.: Rob
Insano Dub Head
Posts: 844
Threads: 90
Registered: December 18th, 2003
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Black
Mood: mystic
|
| posted on February 1st, 2011 at 12:53 PM |
|
|
ok this is a kombi first time apart in 35 years...that ring spanner is 2foot long and i've got 8foot of box section on it. I also have a bar bolted
to the hub to stop it rotating.
it creaked and groaned but it gave in
[img] [/img]
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on February 1st, 2011 at 12:59 PM |
|
|
Yep, kombi's are worse. Bigger axle and rarely undone......I think I've used a hot spanner on two or three bus axles.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
annosL
Officially Full-On Dubber
Posts: 378
Threads: 43
Registered: December 28th, 2008
Member Is Offline
Location: albany
Theme: UltimaBB Pro Blue ( Default )
Mood: need to win lotto
|
| posted on February 1st, 2011 at 11:13 PM |
|
|
It amazes me how these nuts can be torqued up so tight but the thread doesn't strip out of the nut!
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on February 2nd, 2011 at 11:18 AM |
|
|
The type of thread you could use a flogging spanner on would not make any difference when breaking the initial resistance, as long as the car is out
of gear with the hand brake off and the wheels chocked correctly no force would be transmitted to the drive train, but do not use them to torque up
drive nut as you can easly strip the thread as shown in the above photo, only use a torque wrench to apply the correct torque as specified by
volkswagen, I am a senior mechanical technician working off shore and we use various types of torqing devices on power generation and process
equipment under strick guide lines ( not rough mining equipment owned by some one else )and the old flogging spanner when used correctly will cause no
damage, some of out rad guns can generate 4000NM and this is not enough to undo some nuts, but a hit with the correct flogger and the initial
resistance can be broken.
|
|
|
BeetleBob
Learner Dubber
Posts: 1
Threads: 0
Registered: April 4th, 2011
Member Is Offline
Location: Mayberry, USA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 16th, 2011 at 12:04 AM |
|
|
I used a floor jack under the breaker bar with the 36mm socket. Set the hand brake and use the car weight as resistance. The brakes had been replaced
once in 37 yrs. so this was not the first time the axle nut was removed.
Bad back required me to use this technique with the floor jack. |
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
| posted on April 16th, 2011 at 09:08 AM |
|
|
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8650
Threads: 564
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on April 16th, 2011 at 01:06 PM |
|
|
Hi
I've never had one I couldn't get off with a 3/4 bar and socket and a big lump of pipe. I can't believe that people try and undo this sort of nut
with car off the ground, that's just asking for the car to come of the stands..
If have you no luck you can give the nut a whack with a cold chisel in one of the castellated nuts spilt pin holes, drive it towards drum, not down
towards the axle, you will need a new nut.
I have a 3/4 tension wrench, its not much longer than a 1/2 one, I can tension my axle nuts to the correct torque one handed.
Steve
|
|
|
