[ Total Views: 865 | Total Replies: 6 | Thread Id: 88577 ] |
|
tdegens
A.k.a.: Tom Degens
Wolfsburg Wizard
Posts: 425
Threads: 187
Registered: April 5th, 2004
Member Is Offline
Location: Coffs Harbour
Theme: UltimaBB Pro Blue ( Default )
Mood: g
|
posted on February 6th, 2011 at 05:05 PM |
|
|
Beetle stuff for sale
Early Fuel tank with reserve tap $70. Chromed Generator which has the inside coil loose chrome is ok $60. Beetle Motor - F number - that was line
bored by Garry Moody. The case was cleaned and checked and the crank measured and the bearings supplied by north coast engines The top end was ok with
good power and no oil burning. The heads were good. $200.
Metho cooka $40 should work never used it. Looks simple enough gravity feed metho. Water Pump Homda 5.5 hp $60 goes. Also a fasty tank $40. I also
have a 73 Fasty with a working complete motor in place. Good gearbox. Doors, seats, dash gone $500. I can email picies pickies wont load being 124k
Pick up or post with fastway
Tom Degens emerald beach NSW 2456 0266562864 0458562865 tdegens@gmail.com
|
|
baghall
Custom Title Time!
Ben Hal Outlaw Bushranger
Posts: 1021
Threads: 131
Registered: January 15th, 2010
Member Is Offline
Location: Penrith NSW
Theme: UltimaBB Psyche Blue
Mood: Kids think I'm obsessed!
|
posted on February 6th, 2011 at 09:16 PM |
|
|
What type of gearbox is it?
68 Baja - It's a growing pain!
58 Baja ute - and the pain spreads!
85 T3 Kombi - still growing
89 T3 Kombi - parts car
|
|
pickstock
Seriously Crusin Dubber
Posts: 107
Threads: 27
Registered: December 21st, 2010
Member Is Offline
Location: gawler, south aus
Theme: UltimaBB Pro Blue ( Default )
|
posted on February 6th, 2011 at 10:05 PM |
|
|
is the engine running? what does F engine detail (single port, size etc)
does anyone else know shipping to SA??
|
|
tdegens
A.k.a.: Tom Degens
Wolfsburg Wizard
Posts: 425
Threads: 187
Registered: April 5th, 2004
Member Is Offline
Location: Coffs Harbour
Theme: UltimaBB Pro Blue ( Default )
Mood: g
|
posted on February 10th, 2011 at 06:35 PM |
|
|
The motor is crankcase assembled and pcband head sitting in place. Th etinware and exhaust etc needed. New bearings good crank, linebored case.
The gearbox is 1973 standard fasty.
|
|
Calcool
Fahrvergnugen
Posts: 965
Threads: 196
Registered: May 19th, 2005
Member Is Offline
Location: South East of Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Going Shopping in my Trolley
|
posted on February 13th, 2011 at 07:01 AM |
|
|
Can you post some pics of the engine.
I am a bit confused, was it recod and the piston and barrels not fitted up yet, nor the heads?
How long since it was assemled? does it have its flywheel and has this been fitted and end play set?
Are you coming to Brisbane anytime soon?
Cheers,
David
0434 58 22 64
|
|
tdegens
A.k.a.: Tom Degens
Wolfsburg Wizard
Posts: 425
Threads: 187
Registered: April 5th, 2004
Member Is Offline
Location: Coffs Harbour
Theme: UltimaBB Pro Blue ( Default )
Mood: g
|
posted on February 13th, 2011 at 10:22 AM |
|
|
the flywheel is not on, the
pistons barrels and heads are on but not tight. no tinware just bottom end assembled with new bearings and linr bored. cost me $300 so out it goes for
$200
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
posted on February 13th, 2011 at 11:50 AM |
|
|
so fasty motor is running and complete?
what state of health is it in?
|
|