| [ Total Views: 1082 | Total Replies: 3 | Thread Id: 89267 ] |
|
|
 1916baja
Custom Title Time!
Posts: 1990
Threads: 176
Registered: September 20th, 2007
Member Is Offline
Location: Brisbane - Mt Gravatt
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 16th, 2011 at 06:06 AM |
|
|
Crack testing
I'm in QLD, where would i take an engine case to get it crack tested? or is there a method of doing it yourself?
cheers
Mick.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on March 16th, 2011 at 07:15 AM |
|
|
You could do it yourself with kero and talk if you know what to look for (you need good degreaser and preferably compressed air) or get a DyCheck
Crack testing kit from an engineering supply shop or maybe even Repco. Otherwise Crankshaft Engineering at Hillcrest can do a pro job. Ph 3806 7488
Often you'll see a cracked case with the naked eye.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
DubCty
Slammed & Awesome Dubber
Posts: 95
Threads: 11
Registered: June 11th, 2009
Member Is Offline
Location: Launceston, Tas
Theme: UltimaBB Pro Blue ( Default )
Mood: MAD™
|
| posted on March 19th, 2011 at 08:42 PM |
|
|
Gday mate,
Your best bet is a colour contrast water emulsifier Dye check but it is important to follow a few rules
1 - The test surface should be above 15° C and must be extremely clean and free of oil a pre cleaner is included in most kits.
2 - Spray the penetrant/ dye on thick and leave for a minimum of 20 minutes to dwell re apply to any areas that look thin.
3 - Wipe the surface clean with an absorbent cloth until the majority of dye is removed.
4 - Lightly sprinkle the test surface with a water mist and allow a few minutes for the emulsifier to do its job.
5 - wipe the tests surface dry until all of the penetrant/Dye is removed
6 - cover the test surface with a few light coats of developer and allow around 15 minutes for the penetrant to bleed out of any defects
7- If you find the penetrant bleeds out rapidly wipe it off and re cover the area in developer for a clearer picture of what's causing the bleed
out.
Here is a typical example of what a crack would look like.
I hope this helps.
Straight Cuts – The Best Preparation For A Wife!
|
|
|
Thinker
Seriously Crusin Dubber
Posts: 162
Threads: 26
Registered: October 13th, 2008
Member Is Offline
Location: Narellan
Theme: UltimaBB Streamlined2
Mood: Contemplating
|
| posted on March 20th, 2011 at 08:39 AM |
|
|
This stuff works really well
http://www.rocol.com/corp/index.php?option=com_content&view=article&i...
We buy it from blackwoods which you can find online not sure if blackwoods are in QLD
We use it to crack test a 1300 head with the students, with a tiny crack that can only be found using the stuff. We then wash the head with kero and
test again and again.
|
|
|
