A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
posted on August 25th, 2011 at 11:01 PM
very slight gearbox whooooffff noise?
i notice that when i have my baja on, if i engage the clutch, a very low volume, low pitch kinda smooth noise comes from the transmission.
It sounds almost the same as a failed wheel bearing on say a ricer fwd car, cept alot smoother, and faint.
If i disengage the clutch (motor no longer driving the gearbox) it stops. It this something i should be alarmed about?
could it just be noise being transmitted into the cabin because of the gearbox mid strap tensioned on the rear forks not having rubber? or because the
shifter linkage is also solid mount allowing such noise to be heard?
all gears work, and didn't pop out when i took it for a spin. maybe it just needs a run in after sitting so long perhaps...
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
Anthiron
A.k.a.: Nicko McKay
Compulsive Aussie Vee Dubber
The Baja Rejuvenation Begins
Posts: 4936
Threads: 310
Registered: October 1st, 2003
Member Is Offline
Location: Buderim QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Hell hath no fury like a womans scorn for sega.
posted on August 25th, 2011 at 11:13 PM
Throw out bearing (Probobly not)
My bad, read the question wrong.
Nicko
62/60 model bug eye baja bug, (Full Build in Progress)
1974 Chevrolet Luv
1970 MK2 Ford Cortina GT
1979 Yamaha RX125 Two Stroke tracker project.
2004 Harley Davidson Sportster XL Custom
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
posted on August 26th, 2011 at 12:10 AM
hmm. was brand new. maybe flawed. Thanks Nick will have an investigation.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
posted on August 26th, 2011 at 12:14 AM
wait i probably got my wording wrong... the throw out bearing wouldn't make that noise would it if i didn't have my foot on the clutch? or only if i
did?
i put my foot on the clutch and it stops the noise...
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
posted on August 26th, 2011 at 08:14 AM
OK, so I'm no help........is it a 'dog' box?
I'd rather wear a Beetle out by racing it than by polishing it!
1916baja
Custom Title Time!
Posts: 1990
Threads: 176
Registered: September 20th, 2007
Member Is Offline
Location: Brisbane - Mt Gravatt
Theme: UltimaBB Pro Blue ( Default )
posted on August 26th, 2011 at 08:41 AM
Pretty sure the throw out bearing will be noisy if you have your foot off the clutch, push it in, the noise goes away.... i think. I don't think
i've ever had a completley silent throw out bearing... Always new ones. i think it probably amplifies the sound because of the way the gearbox is
mounted. My kombi box was as noisy as hell, but i couldn't kill it!
Mick.
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
posted on August 26th, 2011 at 09:02 AM
Sorry Chris, sounds like main shaft bearing in box to me. Not throwout, they will start thr noise as soon as the bearing contacts the running ring.
Clutch in, goes away, clutch out, noise, worse cold on initial start up.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Originally
posted by 1916baja
Pretty sure the throw out bearing will be noisy if you have your foot off the clutch, push it in, the noise goes away....
Other way around, the throw out bearing is only spinning when you have your foot on the clutch.
Agree with Matt, sounds like the main shaft bearing if it's doing it in all gears as well as neutral.
Silly question but did you check or change the oil before you started driving it?
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
posted on August 26th, 2011 at 06:06 PM
yea its got fresh hypoid gear oil :P, filled till the fill hole.
ah well... will just drive and see how long it lasts i guess lol.
the idea of it being a bearing inside doesn't sound very good at all!
I guess a kombi 3 rib lucky dip at $100 a pop would be the solution if it eventually becomes a problem.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
posted on August 26th, 2011 at 06:16 PM
Quote:
Originally
posted by matberry
Sorry Chris, sounds like main shaft bearing in box to me. Not throwout, they will start thr noise as soon as the bearing contacts the running ring.
Clutch in, goes away, clutch out, noise, worse cold on initial start up.
OUt of curiosity, later down the track what can i expect to happen to this 'dog' () box if i keep driving?
I haven't taken it for a very long drive, i guess i will just play it by ear.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears.
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
posted on August 26th, 2011 at 07:57 PM
Quote:
Originally
posted by bajachris88
OUt of curiosity, later down the track what can i expect to happen to this 'dog' () box if i keep driving?
It'll get worse, how quickly is the point. Really depends on the failure, can be weeks or years, so suck it and see. It'll tell you every startup
how it's going. The worse the bearing gets, the more damage occurs to other components from contaminants and the two shafts getting further apart
causes the gears to wear excessively.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
posted on August 25th, 2011 at 11:01 PM
