| [ Total Views: 854 | Total Replies: 15 | Thread Id: 92338 ] |
|
|
 clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 27th, 2011 at 03:38 PM |
|
|
Fan shround and twin dellortos
Hi guys
Which fan shroud can i use to get more clearance where the twin dellortos touch. I just fitted some empi manifolds and cannot get the carbs on. The
face where the cold start choke assy fits on the dellortos is hitting the fan shroud and they arent even on the studs. The carbs need to be closer to
the centre of the engine by another 30 mm.
Hoping there is a smaller shroud available.
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 27th, 2011 at 04:11 PM |
|
|
I am running DRLA and they fit a 1600 dog house on CB manifolds - just
I thought only Webers had the cold start stuff and that has to be taken off
You could get a 40HP shroud without the heater horns
Futue te ipsum!!!
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on August 27th, 2011 at 06:44 PM |
|
|
Hi
I have twin 40 dels on my sons L bug, they fit nice with a stock fan housing, its all in the manifold. I bought them from Rod Penrose, when I 1st
fitted them they were out way to far, Rod swapped manifolds for and the fit sweet now.
Steve
|
|
|
Aussie Dubbin
Fahrvergnugen
Posts: 895
Threads: 90
Registered: July 21st, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 27th, 2011 at 06:53 PM |
|
|
Could you machine the intake manifold, or would that pull the carbs out of alignment too much?
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 27th, 2011 at 07:33 PM |
|
|
It has a 40hp doghouse shroud on it now, i looked in the SAmba website and they mentioned 40 hp doghouse shrouds cause fitment issues with twin Webers
and Dellortos and that a 36 hp shroud is alot narrower than the 40 hp.
Even if i take the cold start off they still dont fit, will look at the manifolds in the morning too see if i can angle mill them a little.
If all else fails, engine out and cut and weld the current shroud
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 28th, 2011 at 11:27 AM |
|
|
Does anyone have or know where i can get a pair of CB manifolds, part number 3168
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on August 28th, 2011 at 11:30 AM |
|
|
Just about any VW workshop will have some. Have you got the correct linkages for the CB manifolds, the type that are cast into the air filter base?
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 28th, 2011 at 12:20 PM |
|
|
Matt
No linkages, i just took all the stuff from work and i will make up some linkages. We have all the stuff needed for that, R and L dies, rod ends etc
etc.
Just want those manifolds
Edit
Want them bad, like right now.
End edit
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 28th, 2011 at 12:26 PM |
|
|
Can the shroud come off with out pulling the engine.
I cant remember, but you have the two bolts that hold it to the cyl head tins, then there is the oil coller cover,
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on August 28th, 2011 at 01:54 PM |
|
|
shroud can come off with engine in car but it;s a painful job. Need decklid hinge brackets off.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 28th, 2011 at 04:34 PM |
|
|
Thanks Matt, will have a go at that.
I had a look at an engine today that has two webers and what a magic setup, he used a 36 hp shroud and it gives a stack of room between the carbs and
shroud. He even has the choke cables on it and there is still an inch of clearance.
I think i will get one of them shrouds, it just looks alot better .
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on August 28th, 2011 at 09:21 PM |
|
|
Yep, definately the way to go. Beware the new quality fan shrouds.... 
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 29th, 2011 at 03:17 PM |
|
|
I think I had the CB's with a standard super fan shroud with 40 dells. The carbs just touched the site of the fan shroud. I just got a ball peen
hammer and gave it a few small taps to give me 5mm clearance.
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 29th, 2011 at 08:04 PM |
|
|
Hey bix
Ye i know, with the right manifolds they fit but thats with taking the choke of completely, she needs a choke where we live, so i ordered a 36 hp
shroud today, much much better fit can be seen on the many pics at the samba.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on August 29th, 2011 at 09:49 PM |
|
|
Sorta like this
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 29th, 2011 at 09:59 PM |
|
|
Thats it Matt.
That there is a shit load easier to do and it looks dam good and gives a heap of clearance. I reckon its the only way to go.
|
|
|
